My Music Group Limited B56 Manuale Utente
User Guide
PRODUCT OVERVIEW
1. Volume +/Next
2. Power
3. Volume -/Previous
4. Play/Pause/
Answer/Refuse
5. Micro-USB Port
6. Aux
7. LED Indicator
8. Microphone
3. Volume -/Previous
4. Play/Pause/
Answer/Refuse
5. Micro-USB Port
6. Aux
7. LED Indicator
8. Microphone
CHARGING YOUR SPEAKER
Via AC Adapter/Wall Charger: Using the provided
Micro-USB cable, connect your Speaker (Micro-USB port)
to the AC Adapter (USB port).
Via Computer: Using the provided Micro-USB cable,
connect your Speaker (Micro-USB port) to the
computer/laptop (USB port).
A
B
The battery must be fully charged prior to use. It takes approximately
3 hours to fully charge your Speaker (from depleted unit).
Red light ON - unit charging
Red light ON - unit charging
Light OFF - unit fully charged
over
5
6
4
1
7
8
Bluetooth Speaker
2
3
PAIRING THE SPEAKER
TO BLUETOOTH DEVICE
Make sure the Bluetooth function is available and enabled on your
smartphone. Specific pairing procedures will be different depending
on different smartphone models. For detailed information, please refer
to your smartphone’s User Guide.
・
If no device connection is made within 10 minutes of the Speaker
being switched on, the Speaker will automatically turn off to save power.
・
・
After a successful pairing, devices will memorize each other.
Therefore, no manual pairing will be needed next time.
1. Keep the distance between the cell phone and the Speaker
within 3 feet (for pairing only).
2. Turn on the Speaker by pressing and holding the Power
2. Turn on the Speaker by pressing and holding the Power
Button for 3 seconds.
3. The tone prompt will sound and the LED light will flash blue.
3. The tone prompt will sound and the LED light will flash blue.
The unit will automatically enter into pairing mode.
4. Activate the Bluetooth function of the cell phone to search
4. Activate the Bluetooth function of the cell phone to search
for the Bluetooth devices. After finishing the search, select
”“
B56” in the device list displayed.
5. Your AquaBoostBoom Speaker is ready for use.
MUSIC
Go to next song
Press Button.
AUX MODE
・
Keep speaker away from any source of heat.
・
Always adjust the speaker volume to a suitable level to avoid
hearing damage or the damage to the unit.
・
・
If not using the speaker for a long period of time, keep the internal
battery charged (charge once every 3 months). This will extend
the life of your lithium battery.
the life of your lithium battery.
IMPORTANT SAFEGUARDS
SPECIFICATIONS
Frequency: 100Hz ~ 20KHz
Battery: 3.7V/2000mAh
Bluetooth Version: V4.2
Distance: 33 ft (10m)
Charging Time: 3 hours
Playing Time: 8 hours
Battery: 3.7V/2000mAh
Bluetooth Version: V4.2
Distance: 33 ft (10m)
Charging Time: 3 hours
Playing Time: 8 hours
Use the 3.5mm audio cable (included) to
connect the Speaker to an audio source
(MP3/MP4, mobile phone, computer).
A tone will sound. The speaker will play
the music from the audio source.
connect the Speaker to an audio source
(MP3/MP4, mobile phone, computer).
A tone will sound. The speaker will play
the music from the audio source.
NOTE: The Music Function Control only works with
Bluetooth devices that support the A2DP profile.
Go to previous song
Press Button.
MUSIC
SPEAKER CONTROLS
ON/OFF
VOLUME
Volume +
Press and hold Button.
Volume -
Volume -
Press and hold Button.
During a call or when
listening to music:
Press and hold button for
3 seconds to turn the unit ON.
Press and hold the button
again to turn it OFF.
The unit will turn itself off if
inactive for 10 minutes.
3 seconds to turn the unit ON.
Press and hold the button
again to turn it OFF.
The unit will turn itself off if
inactive for 10 minutes.
PLAY/PAUSE/ANSWER/REFUSE THE CALL
Press button to answer the call.
Press and hold button for 2 seconds to refuse the call.
Double press button to call back the last number.
To hang up the call press again.
Press and hold button for 2 seconds to refuse the call.
Double press button to call back the last number.
To hang up the call press again.
TO RESET UNIT
Press button 3 times to reset the Speaker to its original setting.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception,
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception,
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,including
interference that may cause undesired operation.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,including
interference that may cause undesired operation.
which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more
of the followingmeasures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which thereceiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
user is encouraged to try to correct the interference by one or more
of the followingmeasures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which thereceiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
responsible for compliance could void the user's authority to
operate the equipment.