FreeWave Technologies Inc. AMM0921TT Manuale Utente
FreeWave Technologies, Inc. products may be subject to control by the Export Administration Regulations
(EAR) and/or the International Traffic in Arms Regulations (ITAR). Export, re-export, or transfer of these
products without required authorization from the U.S. Department of Commerce, Bureau of Industry and
Security, or the U.S. Department of State, Directorate of Defense Trade Controls, as applicable, is prohibited.
Any party exporting, re-exporting, or transferring FreeWave products is responsible for obtaining all
necessary U.S. government authorizations required to ensure compliance with these and other applicable
U.S. laws. Consult with your legal counsel for further guidance.
(EAR) and/or the International Traffic in Arms Regulations (ITAR). Export, re-export, or transfer of these
products without required authorization from the U.S. Department of Commerce, Bureau of Industry and
Security, or the U.S. Department of State, Directorate of Defense Trade Controls, as applicable, is prohibited.
Any party exporting, re-exporting, or transferring FreeWave products is responsible for obtaining all
necessary U.S. government authorizations required to ensure compliance with these and other applicable
U.S. laws. Consult with your legal counsel for further guidance.
UL Notifications
Models MM2-T-U, MM2-LV-T-U, MM2-MR-R-U, and MM2-MR-T-U are suitable for use in Class 1, Division 2,
Groups A, B, C, and D or non-hazardous locations only. Do not connect or disconnect any connectors while the
circuit is live unless the area is known to be non-hazardous.
Groups A, B, C, and D or non-hazardous locations only. Do not connect or disconnect any connectors while the
circuit is live unless the area is known to be non-hazardous.
Warning! EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR
SUITABILITY FOR CLASS 1, DIVISION 2.
SUITABILITY FOR CLASS 1, DIVISION 2.
Mise en garde ! RISQUE D'EXPLOSION - LA SUBSTITUTION DE COMPOSANTS PEUT
ALTÉRER LES QUALITÉS POUR LA CLASSE 1, DIVISION 2.
ALTÉRER LES QUALITÉS POUR LA CLASSE 1, DIVISION 2.
Warning! DO NOT REMOVE OR INSERT THE DIAGNOSTICS CABLE WHILE THE
CIRCUIT IS LIVE.
CIRCUIT IS LIVE.
Mise en garde ! Ne pas enlever ou insérer le câble de diagnostic alors que le circuit est
sous tension.
sous tension.
Input voltage for the MM2-T-U models is +5.0 VDC. Input voltage for the MM2-LV-T-U models is +3.5 VDC (± 5%).
Input voltage for the MM2-MR-R-U and MM2-MR-T-U models is +6.5 VDC to +30.0 VDC.
Input voltage for the MM2-MR-R-U and MM2-MR-T-U models is +6.5 VDC to +30.0 VDC.
Important:
Input power shall be derived from a single Class 2 power source.
FCC Notifications
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This
device may not cause harmful interference and 2) this device must accept any interference received, including
interference that may cause undesired operation.
device may not cause harmful interference and 2) this device must accept any interference received, including
interference that may cause undesired operation.
This installation guide covers all models of the FreeWave Technologies 900 MHz spread spectrum transceiver sold
under FCC ID KNYAMM0921TT.
under FCC ID KNYAMM0921TT.
All models sold under the FCC ID(s) listed above must be installed professionally and are only approved for use
when installed in devices produced by FreeWave Technologies or third party OEMs with the express written
approval of FreeWave Technologies, Inc. Changes or modifications should not be made to the device.
when installed in devices produced by FreeWave Technologies or third party OEMs with the express written
approval of FreeWave Technologies, Inc. Changes or modifications should not be made to the device.
Warning! The transceivers covered in this guide have a maximum transmitted output power
of 1 W. The antennas used must provide a separation distance of at least 23 cm from all
persons and must not be co-located or operate in conjunction with any other antenna or
transmitter.
of 1 W. The antennas used must provide a separation distance of at least 23 cm from all
persons and must not be co-located or operate in conjunction with any other antenna or
transmitter.
Mise en garde ! Les émetteurs-récepteurs abordés dans ce guide ont une puissance de
sortie maximale de 1 w. Les antennes doivent fournir une distance d'au moins 23 cm de
toute personne et ne doit pas être co-implanté ou fonctionner en conjonction avec toute
autre antenne ou émetteur.
sortie maximale de 1 w. Les antennes doivent fournir une distance d'au moins 23 cm de
toute personne et ne doit pas être co-implanté ou fonctionner en conjonction avec toute
autre antenne ou émetteur.
LIM0001AA Rev E
iii