AeroComm Corporation 44249AJ Manuale Utente

Pagina di 43
AC4424 Specifications
AC4424 Specifications
AC4424 Specifications
AC4424 Specifications    
    
    
    
    
    
5
5
5
5////8/2007
8/2007
8/2007
8/2007    
    34
34
34
34    
    
frequency bins.  Though the RF hardware is still technically half duplex, it makes the radio 
seem full duplex.  This can cause overall throughputs to be cut in half.  Note:  All transceivers 
Note:  All transceivers 
Note:  All transceivers 
Note:  All transceivers 
on the same network must have the same setting for Full Duplex.  
on the same network must have the same setting for Full Duplex.  
on the same network must have the same setting for Full Duplex.  
on the same network must have the same setting for Full Duplex.      
5.2.6
5.2.6
5.2.6
5.2.65.2.5
5.2.5
5.2.5
5.2.5    
Interface Timeout/RF Packet Size
Interface Timeout/RF Packet Size
Interface Timeout/RF Packet Size
Interface Timeout/RF Packet Size    
Interface timeout, in conjunction with RF Packet Size
RF Packet Size
RF Packet Size
RF Packet Size, determines when a buffer of data will 
be sent out over the RF as a complete RF packet based on whichever condition occurs first. 
Interface Timeout
Interface Timeout
Interface Timeout
Interface Timeout – Interface Timeout specifies a maximum byte gap in between consecutive 
bytes.  When that byte gap is exceeded, the bytes in the transmit buffer are sent out over 
the RF as a complete packet. Interface timeout is adjustable in 160uS decrements. The 
actual timeout created by Interface Timeout is equal to the 2's complement of Interface 
Timeout times 160uS. The default value for Interface Timeout is F0H or 2.56ms. 
RF Packet Size 
RF Packet Size 
RF Packet Size 
RF Packet Size – When the amount of bytes in the transceiver transmit buffer equals RF 
Packet Size, those bytes are sent out as a complete RF packet. 
5.2.7
5.2.7
5.2.7
5.2.75.2.6
5.2.6
5.2.6
5.2.6    
Serial Interface Baud Rate
Serial Interface Baud Rate
Serial Interface Baud Rate
Serial Interface Baud Rate    
This two-byte value determines the baud rate used for communicating over the serial 
interface to a  transceiver.  Table 9 
Table 9 
Table 9 
Table 9 ---- Baud Rate
 Baud Rate
 Baud Rate
 Baud Rate lists values for some common baud rates.  
Baud rates below 110 baud are not supported. For a baud rate to be valid, the calculated 
baud rate must be within ±3% of the OEM Host baud rate.  If the 9600_BAUD pin (Pin 12) is 
If the 9600_BAUD pin (Pin 12) is 
If the 9600_BAUD pin (Pin 12) is 
If the 9600_BAUD pin (Pin 12) is 
pulled logic Low at reset, the baud rate will be forced to 9,600
pulled logic Low at reset, the baud rate will be forced to 9,600
pulled logic Low at reset, the baud rate will be forced to 9,600
pulled logic Low at reset, the baud rate will be forced to 9,600.  
.  
.  
.  For Baud Rate values other 
than those shown in Table 9 
Table 9 
Table 9 
Table 9 ---- Baud Rate
 Baud Rate
 Baud Rate
 Baud Rate, the following equation can be used: 
BAUD = (18.432E+06/(32*d
BAUD = (18.432E+06/(32*d
BAUD = (18.432E+06/(32*d
BAUD = (18.432E+06/(32*desired baud rate))
esired baud rate))
esired baud rate))
esired baud rate))    
BaudH= High 8 bits of BAUD (base16)
BaudH= High 8 bits of BAUD (base16)
BaudH= High 8 bits of BAUD (base16)
BaudH= High 8 bits of BAUD (base16)    
BaudL = Low 8 bits of BAUD (base16)
BaudL = Low 8 bits of BAUD (base16)
BaudL = Low 8 bits of BAUD (base16)
BaudL = Low 8 bits of BAUD (base16)    
    
Table 
Table 
Table 
Table 8
8
8
8    –––– Baud Rate
 Baud Rate
 Baud Rate
 Baud Rate    
Baud 
Baud 
Baud 
Baud 
Rate
Rate
Rate
Rate    
BaudL 
BaudL 
BaudL 
BaudL 
(42h)
(42h)
(42h)
(42h)    
BaudH 
BaudH 
BaudH 
BaudH 
(43h)
(43h)
(43h)
(43h)    
Minimum Interface 
Minimum Interface 
Minimum Interface 
Minimum Interface 
Timeout (58h)
Timeout (58h)
Timeout (58h)
Timeout (58h)    
288,00
02h 00h 
FFh 
192,00
03h 00h 
FFh 
115,20
05h 00h 
FEh 
57,600 0Ah  00h 
FDh 
38,400 0Fh  00h 
FCh 
28,800 14h  00h 
FBh 
19,200 1Eh  00h 
F9h