Autostart RTR433 Manuale Utente
Please review the installation guide before
beginning the installation, particularly the wiring
diagram and the list of programming options.
Prior to installation please be sure that all hardware
components required to install the
AS-1200 are in the box.
This is a list of components included in the
AS-1200 kit:
beginning the installation, particularly the wiring
diagram and the list of programming options.
Prior to installation please be sure that all hardware
components required to install the
AS-1200 are in the box.
This is a list of components included in the
AS-1200 kit:
•
1 - AS-1200 control unit
•
1 - 2 button / 3 channel remote transmitter
•
1 - 5 Pin 14 AWG harness (Ignition harness)
•
1 - 7 Pin 18 AWG harness (Main harness)
•
1 - 4 Pin / 2 Wire 18 AWG harness
(Accessories)
•
1 Antenna
•
1 Parts Bag (hood switch, valet switch,
connector, wires)
•
User guide, tech bulletins.
NOTICE:
THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
INSTALLATION POINTS TO REMEMBER
•
When working on a vehicle always leave a
window open.
•
Remove courtesy light fuse if possible to
prevent battery drain.
•
Never Install control unit where it could
interfere with normal operation or obstruct
service technicians.
service technicians.
•
Do not disconnect the battery on vehicles
equipped with air bags and anti-theft radios.
•
Always use a grommet when running wires
into the engine compartment. Never run wires
through bare or sharp metal.
through bare or sharp metal.
•
Always solder and tape all connections.
•
Never ground control unit to vehicle steering
column.
•
Make sure that vehicles equipped with
automatic transmission do not start while in
any of the drive gears. (If it will start in gear
please install a manual transmission starter)
any of the drive gears. (If it will start in gear
please install a manual transmission starter)
FEATURES
§ Dual 12 volt power lines.
§ 12 volt parking light output.
§ 2 Button / 3 channel transmitter.
§ 2 Button / 3 channel transmitter.
§ Factory alarm control.
§ Gasoline or Diesel engine ready.
§ Positive and Negative door lock output.
§ Positive and Negative door lock output.
§ Cold weather timer.
§ Negative trunk output.
§ Up to 600 feet range.
§ Up to 600 feet range.
§ 300 milliamp ground output (pulsed or
constant)
§ 300 milliamp ground when armed output.
§ External trigger control (From external
receiver. e.g.: alarm)
OPTIONS
•
Remote keyless entry
•
Remote Trunk release
•
Engine kill
•
Flashing LED
•
Pager Ready
•
3 YEAR LIMITED WARRANTY
PROGRAMMABLE OPTIONS
•
Door lock pulse duration ( 1 sec, 4 sec, or
two ¼ sec unlock pulses).
•
Ignition controlled door locks.
•
Constant or pulsed Groundout when
running.
•
Run time (5,15, or 25 minutes)
•
Maximum crank duration (6,8, or 12
seconds).
•
Childproof operation.
•
Gasoline or Diesel engine operation.
TRANSMITTER CODE LEARNING
AS-1200 transmitters do not come pre-
programmed. They must be “CODE
LEARNED” at the time of installation. The unit
will hold up to 4 transmitter codes in memory.
To program a new transmitter:
programmed. They must be “CODE
LEARNED” at the time of installation. The unit
will hold up to 4 transmitter codes in memory.
To program a new transmitter:
1. Raise the hood
2. Turn valet switch “off”.
3. Turn ignition “on”.
4. Turn valet switch “on”.Parking lights will
2. Turn valet switch “off”.
3. Turn ignition “on”.
4. Turn valet switch “on”.Parking lights will
turn on for 5 seconds.
5. Press either button on transmitter within 5
seconds of step 4. (lights will flash 5 times
fast, and 2 times slow)
fast, and 2 times slow)