Inovonics Wireless Corporation 3B6OT9UMX Manuale Utente

© Inovonics, 2011 - www.inovonics.com

Installation Instructions - 05177D

The EN1210 is a universal security transmitter.

If you have any problems with this procedure, contact Inovonics 
Wireless technical services:

• E-mail: support@inovonics.com
• Phone: (800) 782-2709

 Figure 1  EN1210 components

1. Pry the top lip of the mounting bracket up, and lift the bracket 

off of the transmitter.

2. Use your thumb to depress the housing release tab on the 

bottom of the transmitter; separate the housing.

3. If replacing a battery, use the hole in the back of the housing 

to push the old battery out of the battery holder.

4. Install the new battery.
5. Press the Reset button to initialize the transmitter.

EchoStream products are able to use a range of radio 
frequencies, and must be configured for your geographic area. 
To configure the transmitter:

1. Place a selection jumper on the appropriate frequency band 

selection pins.

• Place the jumper on the right two pins, marked NZ, to set 

the frequency range to 921-928 MHz for New Zealand.

• Place the jumper on the left two pins, marked AU, to set the 

frequency range to 915-928 MHz for Australia.

• Leave the jumper off the pins to set the frequency range to 

902-928 MHz for North America.

2. Press the Reset button to complete configuration.

Caution: When pressing the Reset button, make sure you don’t 
also touch the frequency band selection pins. Touching the 
frequency band selection pins while pressing the Reset button 
can inadvertently set the EN1210 to the wrong frequency band.

The N/O-N/C selection pins allow the choice of a normally open 
or normally closed state for the contact circuit wired to the input 
terminal.
The transmitter is shipped set for normally closed, with no 
selection jumper on the N/O selections pins.
1. Place a selection jumper on the selection pins to select 

normally open; remove the selection jumper from the 
selection pins to select normally closed.

2. Press the Reset button to complete configuration.

Transmitters must be registered with the system in order to be 
monitored and supervised. Transmitters send a check-in 
message every three minutes. Each transmitter has a unique 
factory-programmed identification number.
Refer to the receiver installation instructions for details on 
registering a transmitter.
1. When prompted by the receiver to reset transmitter, press 

the Reset button.

2. Replace the cover.
3. Test the EN1210 by activating each of the conditions and 

ensuring an appropriate response.

1. Mount the bracket on the wall with the screws provided.
2. Clip the transmitter onto the bracket. Hook the bottom catch 

first, then press the top into place.

3. The housing may be secured with a third mounting screw, 

located beneath the battery.

Note: Accessing this screw on an active transmitter requires 
opening the housing and removing the battery, causing a tamper 
condition.

4. To dismount the EN1210, pull the transmitter housing 

carefully out of the mounting bracket from the top.

External contacts: NO or NC
Distance, external contact to EN1210: 3 meters (10 feet) 
maximum
Typical battery life: 3-5 years
Battery type (BAT604): Panasonic CR123A or equivalent
Operating environment: -20° to 60°C (-4° to 140°F), 
noncondensing

Note: Specifications and data are subject to change without 
notice.

This equipment has been tested and found to comply with the 
limits for a Class B digital device, pursuant to Part 15 of the FCC 
Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular 
installation.  If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and 

receiver.

• Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician 

for help.

This device complies with part 15 of the FCC Rules. Operation is 
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including 

interference that may cause undesired operation.

Note: Changes or modifications not expressly approved by the 
party responsible for compliance could void the user's authority 
to operate the equipment.

Inovonics Wireless Corporation ("Inovonics") warrants its 
products ("Product" or "Products") to conform to its own 
specifications and to be free of defects in materials and 
workmanship under normal use for a period of twenty-four (24) 
months from the date of manufacture. Within the warranty 
period, Inovonics will repair or replace, at its option, all or any 
part of the warranted Product. Inovonics will not be responsible 
for dismantling and/or reinstallation charges. To exercise the 
warranty, the User ("User", "Installer" or "Consumer") must work 
directly through their authorized distributor who will be given a 
Return Material Authorization ("RMA") number by Inovonics. 
Details of shipment will be arranged directly through the 
authorized distributor.
This warranty is void in cases of improper installation, misuse, 
failure to follow installation and operating instructions, alteration, 
accident or tampering, and repair by anyone other than 
Inovonics.
This warranty is exclusive and expressly in lieu of all other 
warranties, obligations or liabilities, whether written, oral, 
express, or implied. There is no warranty by Inovonics that 
Inovonics product will be merchantable or fit for any particular 
purpose, nor is there any other warranty, expressed or implied, 
except as such is expressly set forth herein.  In no event shall 
Inovonics be liable for an incidental, consequential, indirect, 
special, or exemplary damages, including but not limited to loss 
of profit, revenue, or contract, loss of use, cost of down time, or 
interruption of business, nor any claim made by distributor's 
customers or any other person or entity.

A Frequency band 

selection pins

B Reset button

C Antenna

D Input terminal

E N/O - N/C selection pins F Tamper button and spring