Honeywell International Inc. AP100A Manuale Utente
Required Safety Labels
Label location for item number, serial
number, revision information, compli-
ance, and safety information
number, revision information, compli-
ance, and safety information
Product Specifications
Parameter
Specification
Dimensions (Typical):
Height
1.1 inch (28mm)
Length
4.3 inches (109mm)
Width
2.8 inches (71mm)
Weight
2.3 ounces (66g)
Voltage Requirements
5 VDC + 0.5V
Current Draw
100mA @ 5 volts typical
300mA @ 5 volts maximum
300mA @ 5 volts maximum
Temperature Ranges:
Operating
32
° F to +122° F (0° C to +50° C)
Storage
-40
° F to +158° F (-40° C to +70° C)
Radio:
Frequency
2.4 to 2.5 GHz (ISM Band) Frequency
Hopping Bluetooth v.2.1
Hopping Bluetooth v.2.1
Range - AP-010BT
33 ft. (10m) typical
Range - AP-100BT
328 ft. (100m) typical
Data Rate
Up to 1MBps
Humidity
5 to 95% non-condensing
Mechanical Drop
Operational after 50 drops from 3.28 feet
(1 m) to concrete
(1 m) to concrete
Vibration
5G Peak from 22Hz to 300Hz
ESD Sensitivity
Up to 15kV direct air
Up to 8 kV indirect coupling plane
Up to 8 kV indirect coupling plane
Technical Assistance
Contact information for technical support and product service can be
found at
found at
www.honeywellaidc.com
.
Limited Warranty
Refer to
www.honeywellaidc.com/warranty_information
for your
product’s warranty information.
Product Agency Compliance - AP-010BT/AP-100BT
USA
FCC Part 15
This device complies with part 15 of the FCC Rules. Operation is subject to the
FCC Part 15
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1, This device may not cause harmful interference.
1, This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a res-
idential installation. This equipment generates, uses, and can radiate radio fre-
quency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the fol-
lowing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio or television technician for help.
If necessary, the user should consult the dealer or an experienced radio/televi-
If necessary, the user should consult the dealer or an experienced radio/televi-
sion technician for additional suggestions. The user may find the following
booklet helpful: “Something About Interference.” This is available at FCC local
regional offices. Honeywell is not responsible for any radio or television interfer-
ence caused by unauthorized modifications of this equipment or the substitution
or attachment of connecting cables and equipment other than those specified
by Honeywell. The correction is the responsibility of the user.
Use only shielded data cables with this system.
Caution: Any changes or modifications made to this equipment not expressly
Caution: Any changes or modifications made to this equipment not expressly
approved by Honeywell may void the FCC authorization to operate this equip-
ment.
UL Statement
UL listed: UL60950-1.
Canada
Industry Canada
This device complies with Canadian RSS-210. Operation is subject to the fol-
Industry Canada
This device complies with Canadian RSS-210. Operation is subject to the fol-
lowing conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may
2. This device must accept any interference, including interference that may
cause undesired operation.
Conformité à la règlementation canadienne
Cet appareil ISM est conforme à la norme CNR-210 du Canada. Son
Cet appareil ISM est conforme à la norme CNR-210 du Canada. Son
fonctionnement est assujetti aux conditions suivantes :
1. Cet appareil ne doit pas causer de brouillage préjudiciable.
2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le
1. Cet appareil ne doit pas causer de brouillage préjudiciable.
2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le
brouillage pouvant causer un fonctionnement indésirable.
C-UL Statement
C-UL listed: CSA C22.2 No.60950-1-07 for I.T.E product safety.
Europe
The CE marking on the product indicates that this device is in confor-
mity with all essential requirements of the 1999/5/EC R&TTE Direc-
tive and 2011/65/EU RoHS directive. In addition, complies to 2006/
95/EC Low Voltage Directive, when shipped with recommended
power supply.
European contact:
Hand Held Products Europe B.V.
Nijverheidsweg 9-13
5627 BT Eindhoven
The Netherlands
Honeywell shall not be liable for use of our product with equipment
Honeywell shall not be liable for use of our product with equipment
(i.e., power supplies, personal computers, etc.) that is not CE marked and does
not comply with the Low Voltage Directive. This equipment is intended for use
throughout the European Community and has been assessed to the following
standards:
EN 300 328
EN 300 328
EN 301 489-1
EN 301 489-17
EN60950-1
EN60950-1
Waste Electrical and Electronic Equipment Information
Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIA-
Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIA-
MENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and
electronic equipment (WEEE).
This product has required the extraction and use of natural resources for its pro-
duction. It may contain hazardous substances that could impact health and the
environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment and
to diminish the pressure on the natural resources, we encourage you to use the
appropriate take-back systems for product disposal. Those systems will reuse
or recycle most of the materials of the product you are disposing in a sound way.
The crossed out wheeled bin symbol informs you that the product
should not be disposed of along with municipal waste and invites you
to use the appropriate separate take-back systems for product dis-
posal.
If you need more information on the collection, reuse, and recycling systems,
please contact your local or regional waste administration.
You may also contact your supplier for more information on the environmental
performances of this product.
Australia/NZ
C-Tick Statement
Conforms to AS/NZS 3548 EMC requirement
Conforms to AS/NZS 3548 EMC requirement
Russia
Product Agency Compliance - AP-010BT
Class II
Brazil
Mexico
This product meets Cofetel approval.
This product meets Cofetel approval.
Product Agency Compliance - AP-100BT
Class I
China
SRRC Radio Certificate
SRRC Radio Certificate
Patents
For patent information, please refer to
www.honeywellaidc.com/patents
.
Modelo: AP-010BT
0921-11-6583
(01)07898927490089
" Este equipamento opera em caráter secundário, isto é, não tem
direito a proteção contra interferência prejudicial, mesmo de estações
do mesmo tipo, e não pode causar interferência a sistemas operando
em caráter primário."
direito a proteção contra interferência prejudicial, mesmo de estações
do mesmo tipo, e não pode causar interferência a sistemas operando
em caráter primário."
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether
any such changes have been made. The information in this publication does
not represent a commitment on the part of HII.
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether
any such changes have been made. The information in this publication does
not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from the fur-
nishing, performance, or use of this material.
herein; nor for incidental or consequential damages resulting from the fur-
nishing, performance, or use of this material.
This document contains proprietary information that is protected by copy-
right. All rights are reserved. No part of this document may be photocopied,
reproduced, or translated into another language without the prior written con-
sent of HII.
2010-2013 Honeywell International Inc. All rights reserved.
Other product names or marks mentioned in this document may be trade-
marks or registered trademarks of other companies and are the property of
their respective owners.
right. All rights are reserved. No part of this document may be photocopied,
reproduced, or translated into another language without the prior written con-
sent of HII.
2010-2013 Honeywell International Inc. All rights reserved.
Other product names or marks mentioned in this document may be trade-
marks or registered trademarks of other companies and are the property of
their respective owners.
Web Address:
www.honeywellaidc.com