Chic Technology Corporation 2400UP Manuale Utente
Wireless Optical Mouse
with Card Reader Receiver
User's Guide
with Card Reader Receiver
User's Guide
Notice:
Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the users authority to
operate the equipment.
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Congratulations on your purchase of this Wireless Optical Mouse with a Card Reader
Receiver. Please carefully read the User's Guide to learn about the installation and the
convenient and powerful functions of your new Wireless Optical Mouse with the Card
Reader Receiver.
Receiver. Please carefully read the User's Guide to learn about the installation and the
convenient and powerful functions of your new Wireless Optical Mouse with the Card
Reader Receiver.
1. Contents of the Package
1) Wireless Optical Mouse (one channel or two channel)
2) Card Reader Receiver (2-in-1 or 4-in-1 version)
3) Two AA or AAA Batteries for the Mouse
4) CD-ROM for Mouse and Card Reader Drivers
5) User's Guide
2) Card Reader Receiver (2-in-1 or 4-in-1 version)
3) Two AA or AAA Batteries for the Mouse
4) CD-ROM for Mouse and Card Reader Drivers
5) User's Guide
Optional Parts for Wireless Optical Mouse
(The optional parts may be different due to various wireless optical mice.)
(The optional parts may be different due to various wireless optical mice.)
1) AC to DC Adaptor
2) USB to DC Cable
2) USB to DC Cable
2. Install Hardware
2-1. Install the Card Reader Receiver
1) Please turn on your PC.
2) Plug the USB connector of the receiver into the USB port of the PC.
2) Plug the USB connector of the receiver into the USB port of the PC.
2-2. Select the Channel
1) Please skip this section if the mouse has only one channel. The location of the channel
switch may be different due to various mouse shapes.
2) The two-channel switch is located at the back of the mouse or inside the battery case. Select
Channel "1" or "2" .
3) Put the batteries into the battery box.
2-3. Link the Mouse with the Receiver
1) The LED indicator on the receiver will light.
2) Press the Link Button on the receiver and the LED indicator will blink. The receiver is
2) Press the Link Button on the receiver and the LED indicator will blink. The receiver is
ready to automatically link with the mouse.
3) Press the Link Button on the back of the mouse and the LED indicator on the receiver will
blink quickly. The indicator will stay in light while successfully finish the linkage.
4) The LED indicator will blink while you move the mouse.
5) If you need to re-link the mouse or after changing the mouse batteries, please repeat the
above linkage instructions.
6) If the selected channel is interfered by other wireless-mouse users nearby, please change
the Link ID by re-linkage or select the other channel immediately.
3.Install the Drivers
3-1. Notice
1) The driver supports Windows 98, Windows 2000, Windows ME and Windows XP.
2) The driver may be automatically installed.
3) The driver CD-ROM contents the drivers of the mouse and the card reader receiver. Please
2) The driver may be automatically installed.
3) The driver CD-ROM contents the drivers of the mouse and the card reader receiver. Please
select to install the mouse or the card reader receiver
driver at the pop-up window.
driver at the pop-up window.
3-2. Install the Mouse Driver
1) Insert the driver CD-ROM to your PC.
2) If the driver does not be automatically installed, please
2) If the driver does not be automatically installed, please
double click the file "Setup.exe" and follow the setup
instructions to complete the driver installation.
instructions to complete the driver installation.
3) A Mouse Setting icon will appear on the taskbar of
Windows after you successfully finish the installation.
4) You can double click the Mouse Setting icon and follow
the selection instructions to set the mouse button
functions.
functions.
3-3. Select Mouse Functions
1) Double click the Mouse Setting icon.
2) Follow the instructions of the selection items to set the button functions.
2) Follow the instructions of the selection items to set the button functions.
3-4. Install the Driver for the Card Reader Receiver
Notice:
- 4-in-1 Card Reader Receiver: Compatible with CF, SM, MM and SD Cards.
- 2-in-1 Card Reader Receiver: Compatible with CF and SM cards.
- The PC system under Windows ME or Windows XP will automatically detect and install the
- 4-in-1 Card Reader Receiver: Compatible with CF, SM, MM and SD Cards.
- 2-in-1 Card Reader Receiver: Compatible with CF and SM cards.
- The PC system under Windows ME or Windows XP will automatically detect and install the
card reader driver without operating the driver CD-ROM.
1) Insert the driver CD-ROM to your PC.
2) Windows 98 System: Please select the folder of Windows 98. Double click the file
2) Windows 98 System: Please select the folder of Windows 98. Double click the file
Msdriver.exe to install the card reader driver.
3) Windows 2000 System: Please select the folder of Windows 2000. Double click the file
Win2000_driver_setup_v112.msi to install the card reader driver.
4) Data Transfer Rate (From Host) of the 4-in-1 Card Reader Receiver
- Compact Flash Card (CF): 350KB/sec
- Smart Media Card (SM): 250KB/sec
- Multi Media Card (MM): 150KB/sec
- Secure Digital Card (SD): 200KB/sec
- Smart Media Card (SM): 250KB/sec
- Multi Media Card (MM): 150KB/sec
- Secure Digital Card (SD): 200KB/sec
4. Optional Charging Modes for Wireless Optical Mouse
Notice:
Wireless Optical Mouse
with Card Reader Receiver
User's Guide
with Card Reader Receiver
User's Guide
Notice:
Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the users authority to
operate the equipment.
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Congratulations on your purchase of this Wireless Optical Mouse with a Card Reader
Receiver. Please carefully read the User's Guide to learn about the installation and the
convenient and powerful functions of your new Wireless Optical Mouse with the Card
Reader Receiver.
Receiver. Please carefully read the User's Guide to learn about the installation and the
convenient and powerful functions of your new Wireless Optical Mouse with the Card
Reader Receiver.
1. Contents of the Package
1) Wireless Optical Mouse (one channel or two channel)
2) Card Reader Receiver (2-in-1 or 4-in-1 version)
3) Two AA or AAA Batteries for the Mouse
4) CD-ROM for Mouse and Card Reader Drivers
5) User's Guide
2) Card Reader Receiver (2-in-1 or 4-in-1 version)
3) Two AA or AAA Batteries for the Mouse
4) CD-ROM for Mouse and Card Reader Drivers
5) User's Guide
Optional Parts for Wireless Optical Mouse
(The optional parts may be different due to various wireless optical mice.)
(The optional parts may be different due to various wireless optical mice.)
1) AC to DC Adaptor
2) USB to DC Cable
2) USB to DC Cable
2. Install Hardware
2-1. Install the Card Reader Receiver
1) Please turn on your PC.
2) Plug the USB connector of the receiver into the USB port of the PC.
2) Plug the USB connector of the receiver into the USB port of the PC.
2-2. Select the Channel
1) Please skip this section if the mouse has only one channel. The location of the channel
switch may be different due to various mouse shapes.
2) The two-channel switch is located at the back of the mouse or inside the battery case. Select
Channel "1" or "2" .
3) Put the batteries into the battery box.
2-3. Link the Mouse with the Receiver
1) The LED indicator on the receiver will light.
2) Press the Link Button on the receiver and the LED indicator will blink. The receiver is
2) Press the Link Button on the receiver and the LED indicator will blink. The receiver is
ready to automatically link with the mouse.
3) Press the Link Button on the back of the mouse and the LED indicator on the receiver will
blink quickly. The indicator will stay in light while successfully finish the linkage.
4) The LED indicator will blink while you move the mouse.
5) If you need to re-link the mouse or after changing the mouse batteries, please repeat the
above linkage instructions.
6) If the selected channel is interfered by other wireless-mouse users nearby, please change
the Link ID by re-linkage or select the other channel immediately.
3.Install the Drivers
3-1. Notice
1) The driver supports Windows 98, Windows 2000, Windows ME and Windows XP.
2) The driver may be automatically installed.
3) The driver CD-ROM contents the drivers of the mouse and the card reader receiver. Please
2) The driver may be automatically installed.
3) The driver CD-ROM contents the drivers of the mouse and the card reader receiver. Please
select to install the mouse or the card reader receiver
driver at the pop-up window.
driver at the pop-up window.
3-2. Install the Mouse Driver
1) Insert the driver CD-ROM to your PC.
2) If the driver does not be automatically installed, please
2) If the driver does not be automatically installed, please
double click the file "Setup.exe" and follow the setup
instructions to complete the driver installation.
instructions to complete the driver installation.
3) A Mouse Setting icon will appear on the taskbar of
Windows after you successfully finish the installation.
4) You can double click the Mouse Setting icon and follow
the selection instructions to set the mouse button
functions.
functions.
3-3. Select Mouse Functions
1) Double click the Mouse Setting icon.
2) Follow the instructions of the selection items to set the button functions.
2) Follow the instructions of the selection items to set the button functions.
3-4. Install the Driver for the Card Reader Receiver
Notice:
- 4-in-1 Card Reader Receiver: Compatible with CF, SM, MM and SD Cards.
- 2-in-1 Card Reader Receiver: Compatible with CF and SM cards.
- The PC system under Windows ME or Windows XP will automatically detect and install the
- 4-in-1 Card Reader Receiver: Compatible with CF, SM, MM and SD Cards.
- 2-in-1 Card Reader Receiver: Compatible with CF and SM cards.
- The PC system under Windows ME or Windows XP will automatically detect and install the
card reader driver without operating the driver CD-ROM.
1) Insert the driver CD-ROM to your PC.
2) Windows 98 System: Please select the folder of Windows 98. Double click the file
2) Windows 98 System: Please select the folder of Windows 98. Double click the file
Msdriver.exe to install the card reader driver.
3) Windows 2000 System: Please select the folder of Windows 2000. Double click the file
Win2000_driver_setup_v112.msi to install the card reader driver.
4) Data Transfer Rate (From Host) of the 4-in-1 Card Reader Receiver
- Compact Flash Card (CF): 350KB/sec
- Smart Media Card (SM): 250KB/sec
- Multi Media Card (MM): 150KB/sec
- Secure Digital Card (SD): 200KB/sec
- Smart Media Card (SM): 250KB/sec
- Multi Media Card (MM): 150KB/sec
- Secure Digital Card (SD): 200KB/sec
4. Optional Charging Modes for Wireless Optical Mouse
Notice:
F1~F10
Auto Scroll
Backspace
Close Application
Connect to Internet
Control Lock
Control Panel
Copy
Cut
Delete
Double Click
Auto Scroll
Backspace
Close Application
Connect to Internet
Control Lock
Control Panel
Copy
Cut
Delete
Double Click
Down
Drag Lock
End
Enter
Esc
Explorer
Find Computer
Find File
Home
Horizontal
Drag Lock
End
Enter
Esc
Explorer
Find Computer
Find File
Home
Horizontal
Wheel
Interent Explorer
Backward
Interent Explorer
Forward
Lanuch Default
Browser
Lanuch Default
E-mail
Left
Maximize Windows
Middle Button
Maximize Windows
Middle Button
Minimize All
Windows
Minimize
Windows
Page Down
Page Up
Paste
Redo
Right
Page Up
Paste
Redo
Right
Run...
Shift Lock
Shift Lock
Space
Start Menu
System Help
System Property
Start Menu
System Help
System Property
Tab
Undo
Undo
Undo
Undo
Minimize
All Windows
Universal
Universal
Scroll
Universal
Zoom
Up
Figure 3-2-1
Figure 3-2-2
Figure 2-2