Chamberlain Wireless Products Inc. KPD1 Manuale Utente
GCU ID
SW1
SW2
1
off
off
2
on
off
3
off
on
4
on
on
2.1 INSTALLING THE BATTERIES
2.2 SETTING THE GATE CONTROLLER IDENTITY
GATE CONTROL UNIT (GCU) INSTALLATION
- 14 -
- 3 -
Note: Is a ‘Cancel’ button to cancel any call or key sequence.
Note:
To set the identity of
GCU #2, you would position
the
the
dipswitches
as
seen
below.
You can use up to 4 GCU’s with each OWK utilized. If you use more than
1 GCU, the additional units must have their identity set. Changing
dipswitches #1 & #2 on the Gate Control Unit sets the Gate Controller
Identity. (See below.)
1 GCU, the additional units must have their identity set. Changing
dipswitches #1 & #2 on the Gate Control Unit sets the Gate Controller
Identity. (See below.)
Open the GCU by holding the box/shell portion of the unit. Then, while
tilting the bottom section (where the wire is located), pull the box/shell off.
Insert 4 ‘AA’ batteries into the exposed battery holder.
Note: If used in locations that will be below -10°C (20°F), Lithium batteries
are recommended.
Note: Leave the box/shell off until after activation is complete.
tilting the bottom section (where the wire is located), pull the box/shell off.
Insert 4 ‘AA’ batteries into the exposed battery holder.
Note: If used in locations that will be below -10°C (20°F), Lithium batteries
are recommended.
Note: Leave the box/shell off until after activation is complete.
Dipswitch Block
Learn Button
Terminal
Sample Configuration 1:
Open Gate Only
Use this configuration when you wish to use the Reporter Gate System as
an open-only system, which automatically closes, based on a timer or a
magnetic loop.
Enable the Auto-close feature on your Automatic Gate Opener. Connect the
Reporter Gate Controller as shown in the Basic Gate Controller
Installation
an open-only system, which automatically closes, based on a timer or a
magnetic loop.
Enable the Auto-close feature on your Automatic Gate Opener. Connect the
Reporter Gate Controller as shown in the Basic Gate Controller
Installation
diagram. Please refer to your product-specific manual for wiring
information. On the Reporter Intercom, disable gate status checking (as
described above).
described above).
Sample Configuration 2:
Wiring to separate OPEN and CLOSE terminals
Use this configuration when you wish to use the Reporter Gate System to
open and close your gate and check the gate’s last known status, without
connecting to a limit switch or external gate status indicator.
Disable the Auto-close feature on your Automatic Gate Opener.
Connect Contact 2 to Ground, COM, or (-) on your Automatic Gate Opener.
Connect Reporter Gate Controller Contacts 7 and 8 to “Strike Open”, “Open
Only”, “Remote” or a similarly named contact pair on your Automatic Gate
Opener. Please refer to your product-specific manual for wiring information.
If your Automatic Gate Opener has a “Close” or “Close Only” contact pair
(e.g. connecting like a 3-button station), connect Contacts 5 and 6 to the
“Close” contacts.
Slide Gate Controller Dipswitch #5 to the UP position.
If desired, enable Auto-close on the Gate Controller by flipping Gate
Controller Dipswitch #6 to the UP position.
open and close your gate and check the gate’s last known status, without
connecting to a limit switch or external gate status indicator.
Disable the Auto-close feature on your Automatic Gate Opener.
Connect Contact 2 to Ground, COM, or (-) on your Automatic Gate Opener.
Connect Reporter Gate Controller Contacts 7 and 8 to “Strike Open”, “Open
Only”, “Remote” or a similarly named contact pair on your Automatic Gate
Opener. Please refer to your product-specific manual for wiring information.
If your Automatic Gate Opener has a “Close” or “Close Only” contact pair
(e.g. connecting like a 3-button station), connect Contacts 5 and 6 to the
“Close” contacts.
Slide Gate Controller Dipswitch #5 to the UP position.
If desired, enable Auto-close on the Gate Controller by flipping Gate
Controller Dipswitch #6 to the UP position.
LED
Model OWK
9/6/2007
Patents Pending