Lutron Electronics Company Inc 0087 Manuale Utente

Wall

#6 (M3) screw 

recommended

Vertical

Horizontal

1.00

(25.4)

Level Surface

     • Supports system setup and ensures error-free communication between 

system components.

     • Reset button returns the Clear ConnectT Translator to factory settings.
     •Ethernet port for integration and PC connectivity.
     •LED feedback for RF and Ethernet communication.
     • LED feedback for Power status.

 

   Environment 

Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C), 0% to 90% 
humidity, non-condensing. Indoor use only.

   Codes 

Install in accordance with all local and national electrical codes.

   Cleaning 

To clean, wipe with a clean damp cloth. DO NOT use any chemical 
cleaning solutions.

NOTICE - Using a DC adapter not rated at the proper specifications could 
damage the Clear ConnectT Translator and possibly overheat the DC 
adapter. Use only the LutronR DC adapter listed above.

   

RF Device Placement 
 All dimmers, switches, keypads and shades / draperies must be located 
within 30 ft (9 m) of a Clear ConnectT Translator.

 1. Find a suitable location for the Clear ConnectT Translator. 
 2.  Mount vertically or horizontally, as shown in the 

Mounting Diagram, using 

two #6 (M3) screws. When mounting, allow 7 in (177.8 mm) clearance for 
the antenna and ensure convenient access to the power plug. In order to 
achieve proper RF performance, do not mount unit in a metal enclosure.

 3.  Attach the DC adapter cord to the power jack on the Clear ConnectT 

Translator and insert the DC adapter plug into a receptacle.

  Measurements are in inches (mm).

Installation Instructions

Lutron Elec tron ics Co., Inc. 
7200 Suter Road
Coopersburg, PA 18036-1299
P/N 044-297 Rev. A   11/2011

English

NEC is a registered trademark of National Fire Protection Association, Quincy, Massachusetts. Lutron and   are registered trademarks and Clear Connect is a trademark of 
Lutron Electronics Co., Inc.   
© 2011 Lutron Electronics Co., Inc.

Clear ConnectT Translator 

NXB-CCG

5 V

  2 A

DC Adapter: PS-5DC-20-BL

Output: 5 V        2 A 

Typical Power Consumption*: 5 W

Warranty: For warranty information, please see the Warranty enclosed 

with the product, or visit www.lutron.com/resiinfo

Mounting Diagram (side view)

Power Jack (to DC adapter) 
(IEC PELV / NECR Class 2) 
(Model: PS-5DC-20-BL)

CAT5 Cable:
maximum 328 ft
(100 m)

(bottom view)

RF range:
To other devices 30 ft (9 m)

(top view)

 

Ethernet

Pin #

T+Ve

1

T-Ve

2

R+Ve

3

R-Ve

6

* Typical Power Consumption test conditions: one LED on, Ethernet cable plugged in, 

Clear ConnectT Translator powered by the 5 V   adapter supplied.

Clear ConnectT Translator

6.25

(158.8)

4.42

(112.3)

2.72

(69)

1.30 

(33)

2.60

(66)

30 ft (9 m) maximum

Reset Button 

Press and hold 

for 30 seconds to 

restore the system 

to the Factory 

settings.

USB Cable: 
(Lutron use only)

Displays the Tx / Rx 
activity on the RF link. 

Power/Status LED 

Displays power status 
and other system status 
indicators.

Displays the connection 
status and Tx / Rx activity 
on the Ethernet link. 

This device complies with part 15 of the FCC Rules and Industry Canada license-

exempt RSS standard(s). Operation is subject to the following two conditions: (1) This 

device may not cause interference, and (2) this device must accept any interference, 

including interference that may cause undesired operation. Modifications not expressly 

approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this 

equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation. If this equipment does cause harmful interference to 

radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the 

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Returning a Clear ConnectT Translator to Factory 

Note: Returning a Clear ConnectT Translator to factory settings will erase 

ConnectT Translator to be reprogrammed into the system.

1.   Press and hold the Reset button on the Clear ConnectT Translator for 

30 seconds.

2.  The Power/Status LED will start flashing slowly for approximately 

10 seconds after which it will start rapidly flashing for approximately 

20 seconds and then remain on.

3. The Clear ConnectT Translator has been returned to factory settings.