Lutron Electronics Company Inc 0096 Manuale Utente

Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.

RF Relay Module | Installation

with SoftswitchR

041423

Rev. A

08/2013

Important Notes:

•

For installation by a qualified electrician in accordance

with all local and national electrical codes.

• Note: Use copper conductors only.
• Check to see that the device type and rating is suitable

for the application.

• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product

to dry completely before installation.

•  Operate between 32 °F to 131 °F (0 °C to 55 °C).
•  0% to 90% humidity, non-condensing.
•  For indoor use only.

Please read before installing

LMJ-16R-DV-B

120 / 277 V~ 50 / 60 Hz 16 A

1/2 HP at 120 V~ 1

⁄

HP at 277 V~

UL 2043 Plenum Rated

LMK-16R-DV-B

LMN-16R-DV-B

LMM-16R-DV-B

LMQ-16R-DV-B

220 - 240 V~ 50 / 60 Hz 16 A

6 A Motor (LMK- Model)

FCC Information:

(LMJ- model only)

This device complies with part 15 of the FCC Rules and

Industry Canada license-exempt RSS standard(s). Operation is

subject to the following two conditions:

(1) This device may not cause interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation.

Modifications not expressly approved by Lutron Electronics Co.,

Inc. could void the user’s authority to operate this equipment.
NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or

more of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Warranty:

For warranty information, please visit
www.lutron.com/TechnicalDocumentLibrary/Warranty.pdf
www.lutron.com/TechnicalDocumentLibrary/Intl_Warranty.pdf

Lutron and are registered trademarks of Lutron Electronics

Co., Inc.

Load

Status

LED

Relay Toggle

Advanced

Operations

For System Setup Guide and tools
visit www.lutron.com

RF Relay Module

RF Relay Module Operation

Reset Factory Defaults

Note: In some instances it may be

necessary to reset the RF Relay Module

back to factory default settings.

Triple-tap the Advanced Operations

(“ADV”) button, on the RF Relay

Module and hold until the LED

begins to flash slowly.

Within 3 seconds of flashing,

release and triple-tap the button

again and the LED will flash

rapidly indicating that the unit has

been reset to factory defaults.

Note: Any associations or programming

previously set up with the unit will be lost

and will need to be re-programmed.

Troubleshooting

English

When installing a RF Relay Module,

use the supplied conduit nut and

wire the module as shown.

If installing unit inside a junction box,

please see Application Note #423.
For more information: www.lutron.com

Installation:

LMJ-, LMQ-, and LMM- models

Conduit Nut

White

(Neutral)

Black

(Hot)

Red

(Switched Hot)

To Load

Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com

RF Relay Module can be installed

in a junction box or marshalling

box (optional) using the conduit nut

(provided) or with mounting screws

(not provided). Please consult local

and national electric codes for

proper installation.

RF Relay Module Placement

RF Relay Modules must be located within 30 ft (9 m) of an RF signal repeater. RF relay modules cannot

be controlled by the system until they are programmed using the system programming software.

Shock Hazard. May result in

serious injury or death.

Turn off power at circuit breaker

before installing the unit.

WARNING

Installation:

LMK- and LMN- models

Blue (LMK-), Black (LMN-)

(

Neutral

)

Brown (LMK-), Red (LMN-)

(

Line

)

Black (LMK-), Yellow (LMN-)

(Switched Line)

Conduit Nut

21 mm knockout opening

To Load

For

LMN-16R-DV-B use supplied Twist-on wire

connectors. (3 supplied)

10 mm

Wiring a Lever Operated Connector (shown)

When wiring lever operated connectors (3 supplied)

please use 14 AWG to 12 AWG (2.5 mm

to 4.0 mm

)

diameter solid or stranded copper wire.

220 - 240 V~ 50/60 Hz

Load does

not respond

to Wireless

Transmitter(s).

• Ensure breaker to the

RF Relay Module is on.

• Ensure the load has

been properly wired to
the RF Relay Module.

• Ensure that the RF

Relay Module has been
activated in the system.

• Ensure that the Wireless

Transmitter battery is
installed correctly.

RF Relay

Module does

not respond

to a keypad,

wireless

controller or

sensor.

• Improper programming.

Program from the
system programming
software.

• Out of RF Range.

Reposition to be within
30 ft (9 m) of an RF
signal repeater.

• Already at current level.

The RF Relay Module
has already responded
to a command, or is
already at the requested
setting.

• Wireless controller or

sensor batteries low
or installed incorrectly.
Replace or install
batteries properly.

• RF interference.

Do not run RF Relay
Module wires with
other power wires or
communication wires
(e.g., networking, audio,
or video signals).

120/277 V~ 50/60 Hz (LMJ- model)
220 - 240 V~ 50/60 Hz (LMQ- and LMM- models)