EMS Technologies Canada Ltd. A781-MK2 Manuale Utente
ABBREVIATED COMPONENT MAINTENANCE MANUAL
1458-A-1101 / 1458-A-1300
INTRODUCTION
1.
How to Use This Manual (TASK 23-15-30-99F-801-A01)
A.
General (Subtask 23-15-30-99F-001-A01)
(1)
This publication gives maintenance instructions for the equipment shown on the Title page.
(2)
Standard maintenance procedures that technicians must know are not given in this manual.
(3)
This publication is written in agreement with the ATA Specification.
(4)
Refer to the Special Tools, Fixtures, and Equipment and Consumables tables in each section
before the start of maintenance procedures.
before the start of maintenance procedures.
(5)
Honeywell recommends that you do the tests in TESTING AND FAULT ISOLATION (PGBLK
23-15-30-1000) to test the operational status of the unit. These tests can show the condition
of the unit or most possible cause of a malfunction. If a malfunction occurs, the unit must
be returned to the manufacturer for fault isolation and repair, refer to APPENDIX A (RMA)
(PGBLK 23-15-30-1700).
23-15-30-1000) to test the operational status of the unit. These tests can show the condition
of the unit or most possible cause of a malfunction. If a malfunction occurs, the unit must
be returned to the manufacturer for fault isolation and repair, refer to APPENDIX A (RMA)
(PGBLK 23-15-30-1700).
(6)
Maintenance for the A350 SDU and SCM system is limited to replacement on verified failure.
After consultation with a Honeywell product support specialist and if replacement of the unit
is deemed necessary, refer to APPENDIX A (RMA) (PGBLK 23-15-30-1700) for equipment
return procedures.
After consultation with a Honeywell product support specialist and if replacement of the unit
is deemed necessary, refer to APPENDIX A (RMA) (PGBLK 23-15-30-1700) for equipment
return procedures.
(7)
All repairs must be performed at Honeywell or a Honeywell approved repair facility.
(8)
Warnings, cautions, and notes in this manual give the data that follows:
• A WARNING gives a condition or tells personnel what part of an operation or maintenance
procedure, which if not obeyed, can cause injury or death
• A CAUTION gives a condition or tells personnel what part of an operation or maintenance
procedure, which if not obeyed, can cause damage to the equipment
• A NOTE gives data, not commands. The NOTE helps personnel when they do the related
instruction.
(9)
Warnings and cautions go before the applicable paragraph or step. Notes follow the applicable
paragraph or step.
paragraph or step.
B.
Observance of Manual Instructions (Subtask 23-15-30-99F-002-A01)
(1)
Make sure that you carefully obey all safety, quality, operation, and shop procedures for the unit.
(2)
All personnel who operate equipment and do maintenance specified in this manual must know
and obey the safety precautions.
and obey the safety precautions.
C.
Symbols (Subtask 23-15-30-99F-003-A01)
(1)
The symbols and special characters are in agreement with IEEE Publication 260 and IEC
Publication 27. Special characters in text are spelled out.
Publication 27. Special characters in text are spelled out.
(2)
The signal mnemonics, unit control designators, and test designators are shown in capital
letters.
letters.
(3)
The signal names followed by an “*” show an active low signal.
(4)
The symbols in Figure 1 (GRAPHIC 23-15-30-99B-801-A01) show ESDS and moisture
sensitive devices.
sensitive devices.
EFFECTIVITY
ALL
23-15-30
Page 7 of 70
5 Oct 2012
© Honeywell International Inc. Do not copy without express permission of Honeywell.
Interim
DRAFT
for
FCC
Approval
Purposes
Do
Not
Use
for
Maintenance
10-Feb-2013