VTech Telecommunications Ltd 80-9395-01 Manuale Utente

on purchasing your new VTech product. Before 
using this product, please read 

safety instructions. 

For support, shopping, and everything new at 
VTech, visit our website at  
www.vtechphones.com.

Register your product online for 

enhanced warranty support.

Learn about the latest VTech  
products.

You can power up the parent unit by connecting 
it to AC power or to the rechargeable battery 
provided. Even if the parent unit is connected to  
AC power, we recommend you also install the 
battery. This guarantees continual operation in 
case of a power outage.
Install the battery as shown below.

Press down on the large tab of the battery 
compartment cover and pull it out.

1.

With the label

 THIS SIDE UP facing up, 

insert the small tabs of the battery into the 
slots inside the battery compartment. Make 
sure the metallic contact is correctly oriented 
as shown below. Push the battery into the 
battery compartment until it clicks securely 
into place.

Align the battery compartment cover flat 
against the battery compartment, then slide 
it towards the center of the parent unit until it 
clicks into place

.

To replace the battery, press down on the large 
tab of the battery compartment cover and pull 
it out, then follow the steps above to install the 
battery.

NOTES

The operating time for using the rechargeable 

battery is short. If you want to monitor your baby for 

a long time, we recommend you connect the parent 

unit to AC power.
If the parent unit will not be used for a long time, 

disconnect and remove the battery to prevent 

possible leakage.

2.

3.

•

•

NOTES

Use only the battery supplied with this product.
Use only the power adapters supplied with this 

product.
Make sure the electrical outlets are not controlled 

by wall switches.
The power adapter are intended to be correctly 

oriented in a vertical or floor mount position. The 

prongs are not designed to hold the plug in place if 

they are plugged into a ceiling, under-the-table or 

cabinet outlet.
Make sure the parent unit, the baby unit and the 

power adapter cord are out of reach of children.

•
•

•

•

•

Once you have connected the parent unit and 
installed its battery

, the parent unit powers on 

automatically. 

The battery icon indicates the 

battery status (see the following table).

NOTES

The parent unit battery is fully charged after  

12 hours of continuous charging.
It takes longer to charge the battery when the 

parent unit is turned on. To shorten the charging 

time, turn the parent unit off while charging.
The standby time varies depending on the 

sensitivity level you set, your actual use and the 

age of the battery.

The battery 
icon is off 
and   
displays.

No battery 
is installed 
but operates 
using AC 
power, or the 
battery has 
been installed 
incorrectly.

Install the 
parent unit 
battery. 
Charge without 
interruption  
(at least  
30 minutes).

The screen 
displays 

and 

. 

The 

 light

light 

flashes.

The battery 
has very little 
charge and 
may be 

used 

for only a 
short time.

Charge without 
interruption 
(about  
30 minutes).

The battery 
icon 
becomes 
solid 

.

The battery is 
fully charged.

To keep 
the battery 
charged, 
connect it to 
AC power 
when not in 
use.

•

•

•

You may test the baby monitor before initial use, 
and at regular times thereafter. 
To test your baby monitor:

Place the parent unit and the baby unit in the 
same room to test the product. Make sure 
the baby unit is at least 1 meter / 3 feet away 
from the parent unit.
Slide 

ON/OFF on the baby unit to turn it on.

Upon initial use, the parent unit powers on 
automatically after connecting to AC power. 
The screen shows 

®

 and 

on.... 

NOTE

If both units are not connected, the parent unit displays 

No link to CAM # (#

 represents the selected baby 

unit number

) and 

Linking... on the screen. The LINK 

light first flashes and then turns off. Move the parent 

unit closer to the baby unit.

1.

2.

3.

NOTE

This baby monitor is intended as an aid. It is not a 

substitute for proper adult supervision, and should not 

be used as such.

CAUTION

Keep the baby unit out of the reach of your baby. 

Never place or mount the baby unit inside the baby’s 

crib or playpen.

Place the baby unit at least 1 meter / 3 feet 
away from your baby.

2. 

Place parent unit at least 1 meter / 3 feet 

away from the baby unit.

NOTE

If you experience audio feedback on either the parent 

unit or baby unit, move the parent unit further away 

until there is no more audio feedback.

TIP

You can increase the speaker volume of the parent 

unit if you cannot hear the sounds transmitted from 

the baby unit.

The operating range of the baby monitor is up to 
300 meters (1,000 feet) outdoors or 50 meters 
(160 feet) indoors. The actual operating range 
may vary depending on the environmental 
conditions and other interferences such as 
walls, doors and other obstructions. 

1.

1

2

3

4

5

6

7

8

On when the baby unit is turned on 

and is paired to the parent unit.

Flashes when the baby unit is pairing 

to the parent unit.

•

•

9

Slide to turn on or off the baby unit.

•

10

Press to adjust the listening volume.

•

11

Press and hold to pair to the parent 

unit when a desired baby unit slot is 

chosen at the parent unit. 

•

12

For wall mount installation use.

•

1

2 

3

4

5

Indicate the different statuses of 

the parent unit. For details, refer to 

Parent unit lights. 

•

6

7

 On/off
Press to power on.
Press and hold to power off.

•
•

8

While viewing image, press and hold 

to talk to the selected baby unit.

•

9

 Zoom
While viewing image, press to zoom 
in or out. 

•

10

While in a menu, press to select a 

feature.
While viewing image, press and hold 

to move the image rightward.

•

•

11

While in a menu, press to return to 

the main menu or idle screen.
While viewing image, press and hold 

to move the image leftward.

•

•

12

Press to view the image of the next 

registered baby unit in  

SINGLE-CAM mode.
Press and hold to turn off the parent 

unit screen.

Press to turn on or off the 

function.

Press to turn on or off the  

SPLIT-VIEW mode.

•

•

•

•

13

Press to increase the speaker 

volume.

•

14

Press to decrease the speaker 

volume.

•

15

Press to enter the menu.
While in a menu, press to choose an 

item, or save a setting.

•
•

16

While in a menu, press to scroll up.
While viewing image, press and hold 

to move the image upward.

•
•

17

While in a menu, press to scroll 

down.
While viewing image, press and hold 

to move the image downward.

•

•

On when moderate or high signal 

strength is detected between the 

parent unit and the selected baby unit.
Flashes when low signal strength is 

detected between the parent unit and 

the selected baby unit.
Off when the parent unit is turned off, 

or the link to the selected baby unit is 

lost.

On when the parent unit battery is 

charging.
Flashes when the parent unit battery 

is low and needs charging.
Off when the parent unit is turned off, 

charged without battery, or when the 

battery inserted is fully charged or not 

being charged.

On when the parent unit is talking to 

the baby unit.

On when the speaker volume of the 

parent unit is turned off.

 displays when strong signal 

strength is detected between the 

baby unit and the parent unit.

 or   displays when moderate 

or low signal strength is detected 

between the baby unit and the 

parent unit.

 displays when the link between 

the baby unit and the parent unit  

is lost.

•

•

•

 or 
 or 
 or 

Displays the number of the baby 

unit that is being viewed when in  

SINGLE-CAM mode.
Displays the highlighted baby unit 

when in 

SPLIT-VIEW mode.

•

•

Displays when the parent unit is in 

PATROL mode.

•

Displays when the camera has 

activated the night viewing feature. 

•

Displays when the camera at the 

baby unit has zoomed in.

•

Displays when the temperature 

alert is set on.

•

57 

o

F  

or  
14 

o

C

Displays the real-time temperature 

of the selected baby unit.

•

Displays when the speaker volume 

is set to off.
Displays when 

SPLIT-VIEW mode 

is turned on.

•

•

or

Displays the sound level according 

to the scales of loudness when 

there is sound transmitted from 

the baby unit.

Displays the speaker volume level 

while adjusting.

•

•

Displays when there is only one 

paired baby unit and the low 

radiation mode is in use.

•

 animates 

when the battery is charging.

 displays solid when the battery 

is fully charged.

 displays when the battery is 

low and needs charging.

•

•

•

Displays when the parent unit is 

connected to AC power without 

the battery.

•

You can select a language (English, 

French or Spanish) to be used in all 

screen displays.

Alert tone
You can set the parent unit to beep 

when

the parent unit operates in low 
battery condition;
the link between the parent unit 

and the baby unit is lost; or
the baby unit detects sounds while 

in 

SPLIT-VIEW mode.

•

•

•

Sensitivity
With this feature, you can choose 

to hear sounds from the baby unit 

all the time, or to hear sounds that 

exceed a certain level. You can 

use the parent unit to adjust the 

microphone sensitivity of your baby 

unit. The higher the sensitivity level, 

the more sensitive the baby unit is in 

detecting sounds for transmitting to 

the parent unit.

Temperature
You can turn on the temperature 

alert feature so that the parent 

unit beeps whenever the room 

temperature detected by the 

baby unit falls out of the desired 

temperature range.

Vibration
You can turn on the vibration alert so 

that the parent unit vibrates when

the baby unit detects sounds while 

in 

SPLIT-VIEW mode;

the link between the parent unit 

and the baby unit is lost; or
the temperature detected by the 
baby unit falls out of the preset 
temperature range.

•

•

•

Sound-activated screen 
Automatically turns on the parent 
unit screen when a sound is 
detected in your baby’s room. When 
no sound is detected, the screen is 
off to save power.

Brightness
You can change the brightness of 

the parent unit screen.

Rename
You can choose a specific name 

for the baby unit from a pre-defined 

name list.

Pair/unpair
The baby unit and parent unit 

provided are already paired. You can 

add or replace baby units (

VM305, 

purchased separately) to your baby 

monitor system.

 No link to  

CAM # (# represents 

the selected baby 

unit number).

The selected baby unit is 
out of range or is turned 
off.

The battery level of 
the parent unit is very 
low and needs to be 
recharged.

The battery is empty and 
needs to be recharged.

(

# represents the 

selected baby unit 

number).

The sound level exceeds 
the threshold at CAM # in 
SPLIT-VIEW mode.

(

# represents the 

selected baby unit 

number).

The temperature detected 
from the selected baby 
unit is below the selected 
minimum temperature.

(

# represents the 

selected baby unit 

number).

The temperature detected 
from the selected baby 
unit is above the selected 
maximum temperature.

The parent unit is turning 
on. 

The parent unit is 
searching for baby units 
when the link is lost.

Slide 

ON/OFF to the left to turn on the baby 

unit. The 

ON/OFF LED light turns on.

Slide 

ON/OFF to the right to turn off the 

baby unit. The 

ON/OFF LED light turns off.

Press   to turn on the parent unit. The 

LINK 

light turns on.
Press and hold   again to turn off the 

parent unit. The 

LINK light turns off.

You can turn on or off the parent unit screen 
without powering off the parent unit. You can 
still hear sound from the baby unit.

Press and hold 

VIEW on the parent unit to 

turn off the screen.
Press any key on the parent unit to turn on 

the screen again.

Press 

VOL+ or VOL- on the parent unit at 

any time when viewing images.

NOTE

When the parent unit speaker volume is set to zero,  

 appears on the screen and the   light turns on.

Press VOL+ or 

VOL- on the baby unit at 

any time.

•

•

•

•

•

•

•

•

You can select a language (English, French or 
Spanish) to be used in all screen displays.

Press 

MENU when the parent unit is not in 

use.
Press   or   to choose 

LANGUAGE, then 

press 

SELECT.

Press   or   to choose 

English, Français 

or 

ñol, then press SELECT to confirm 

your selection. 

You can change the brightness of the parent unit 
screen from 

Level 1 to Level 5. 

Press 

MENU when the parent unit is not in use.

Press   or   to choose 

BRIGHTNESS, then 

press 

SELECT.

Press   or   to choose the desired level of 

brightness, then press 

SELECT to confirm 

your selection. 

You can choose to hear sounds from the baby 
unit all the time, or to hear sounds that exceed 
a certain level. You can use the parent unit to 
adjust the microphone sensitivity of your baby 
unit from 

Level 1 to Level 5. The higher the 

sensitivity level, the more sensitive the baby 
unit is in detecting sounds for transmitting to the 
parent unit. The sound sensitivity is preset to 
Level 3.

1.

2.

3.

1.
2.

3.

Sensitivity

Description

High 

sensitivity

Low 

sensitivity

High sensitivity level
The parent unit speaker is 
constantly on, and you will 
hear all sounds (including 
background noises) from 
your baby’s room.

Medium high  
sensitivity level
The parent unit speaker 
turns on for soft babbling 
and louder sounds from your 
baby. It remains quiet when 
your baby sleeps soundly.

Medium sensitivity level
The parent unit speaker 
turns on for loud babbling 
and louder sounds from 
your baby. It remains quiet 
when your baby makes soft 
sounds.

Medium low  
sensitivity level
The parent unit speaker 
turns on for crying and louder 
sounds from your baby. It 
remains quiet when your 
baby makes soft sounds.

Low sensitivity level
The parent unit speaker 
turns on for loud crying or 
screeching sounds from 
your baby. It remains quiet 
when your baby makes soft 
sounds.

Press 

MENU when the parent unit is not in 

use.
Press   or   to choose 

SENSITIVITY, then 

press 

SELECT. 

If you have more than one baby unit, 

the system prompts you to choose the 

desired baby unit or all baby units, press 

 or   to choose 

All CAM or CAM #, 

then press 

SELECT.

Press   or   to choose the desired 

sensitivity level, then press 

to 

confirm your selection.

TIP

You can adjust the baby unit placement to improve 

the sound detection

1.

2.

•

3.

The parent unit continuously monitors the sound 
level in your baby’s room. When the sound 
activation mode is on, the parent unit screen 
turns on when the baby unit detects a sound.
As long as no sound is detected within  
50 seconds, the parent unit screen is off to 
save power. When your baby starts to cry, the 
sound activation triggers the parent unit screen 
automatically turns on.

Press 

MENU when the parent unit is not in 

use.
Press   or   to choose  

SOUND-ACTIVATED SCREEN,  

then press 

SELECT.

Press   or   to choose 

On or Off, then 

press 

SELECT to confirm your selection.

NOTE

NOTES

If you mute the speaker while sound activation 

is on, then you hear a beep sound whenever the 

screen turns on.
If you want to turn on the parent unit screen 

continuously while the sound activation is on, then 
set the sound sensitivity to 

Level 5.

Every time you turn on the parent unit, you 
enter the 

SINGLE-CAM mode. The screen 

displays image of a particular baby unit in full 
screen. If there are more than one baby units 
in your system, you can also monitor in the 
SPLIT-VIEW mode, where the screen displays 
a maximum of four baby units in one screen. 

Press 

VIEW repeatedly to view images of 

other baby units.
Press 

PATROL to display images from 

different baby units in every 7 seconds. Press 
again to turn off the patrolling function.

Press 

SPLIT key to enter the SPLIT-VIEW 

mode. 

Press  ,  ,   or   to select a baby unit.
Press   or 

VIEW key to view images from 

the selected baby unit temporarily in  
SINGLE-CAM mode. It returns to  
SPLIT-VIEW mode after 10 seconds.

1.

2.

3.

•

•

•

•

•

•
•

BC

1

2

3

1

2

3

At least 1 meter

(3 feet) 

d

e

f
g
h
i

j
k

l

m
n
o

p
q

a

b

c

At least 1 meter 

(3 feet)