VTech Telecommunications Ltd 80-9982-00 Manuale Utente

Press select to confirm your selection.

TIP

To enter the sensitivity menu of the parent unit, the 
baby unit must be turned on.

You may turn on the sound alert while the speaker 
volume is turned off so that the parent unit beeps 
as soon as the baby unit detects sounds which 
light up four sound level indicators on the parent 
unit.
When the sound alert of the parent unit is turned 
on, 

displays. The sound alert is preset to OFF.

Press menu when the parent unit is not in 
use.

Press volume + or volume - to choose 
SOUND ALERT

, then press select.

Press volume + or volume - to choose ON
or OFF.
Press select to confirm your selection. The 
screen displays SAVED and you hear a 
confirmation tone.

NOTE

The sound alert setting on each parent unit is 
independent.

You may turn on the vibration alert so that the 
parent unit vibrates as soon as the baby unit 
detects sounds which light up four sound level 
indicators on the parent unit.
When the vibration alert of the parent unit is turned 
on, 

displays. The vibration alert is preset to 

.

Press menu when the parent unit is not in 
use.

Press volume + or volume - to choose 
VIBE ALERT

, then press select.

Press volume + or volume - to choose ON
or OFF.
Press select to confirm your selection. The 
screen displays SAVED and you hear a 
confirmation tone.

NOTES

Each time you set the vibration alert to ON, the 
parent unit vibrates briefly after you press 

.

The vibration alert setting on each parent unit is 
independent.

4.

1.

2.

3.

4.

Ć

1.

2.

3.

4.

Ć

Ć

NOTE

Make sure the supplied rechargeable battery with the 
label THIS SIDE UP facing up.

BC

You can power up the parent unit by connecting 
it to AC power or to the rechargeable battery 
provided. Even if the parent unit is connected to 
AC power, we recommend you also install the 
battery. This guarantees continual operation in 
case of a power outage.

NOTE

Use only the battery supplied with this product

.

Install the battery as shown below.

To replace the battery, unplug the battery 
connector from the socket, and then pull the 
battery out of the battery compartment. Follow 
the steps above to install the battery.

NOTES

The operating time for using the rechargeable 
battery is short. If you want to monitor your baby for 
a long time, we recommend you connect the parent 
unit to AC power.

If the parent unit will not be used for a long time, 
disconnect and remove the battery to prevent 
possible leakage.

Ć

Ć

Once you have

 connected the parent unit and 

installed its battery, press

to turn it on. The 

battery icon indicates the battery status (see the 
following table).

NOTES

The parent unit battery is fully charged after 11 
hours of continuous charging.

It takes longer to charge the battery when the 
parent unit is turned on. To shorten the charging 
time, turn the parent unit off while charging.

The standby time varies depending on the 
sensitivity level you set, your actual use and the 
age of the battery.

The battery 
icon is off.

No battery is 
installed. The
parent unit 
can be used
only when it is 
connected to
AC power.

Install the 
parent unit 
battery.
Charge without 
interruption
(at least 30 
minutes).

and 

flash on the 
screen. 

The

 light 

flashes.

The battery 
has very little 
charge and 
may be used 
for only a short 
time.

Charge without
interruption
(about 30 
minutes).

The battery 
icon 
becomes 
solid 

.

The battery is 
fully charged.

To keep the 
battery charged, 
connect it to AC 
power when not 
in use.

Ć

Ć

Ć

You may test the baby monitor before initial use, 
and at regular times thereafter. 

Place the parent unit and the baby units in 
the same room to test the product. Make 
sure the baby unit is at least 3 feet away 
from the parent unit.

Press 

 to turn on

 the baby unit. 

The power on lights up.

Press

 to turn on the parent unit. The 

screen turns on.

NOTE

I

f both units are not connected, the parent unit 

displays NOT LINKED and

 flashes.

1.

2.

3.

1

When it is on, it projects some image 
patterns to the user environment.
When it is on, it plays lullaby.

Ć

Ć

2

3

Press to power on.
Press and hold to power off.
Flashes when the baby unit is not 
linked to a parent unit; or the pairing 
process is in progress.

Press to start or stop paging parent 
unit.

Press to increase the listening 
volume.

Press to decrease the listening 
volume.

Press to turn on or off the projector.

Ć
Ć
Ć

Ć

Ć

Ć

Ć

4

5

6

1

2

The visual sound indicator has two 
functions. One is to show the sound level 
detected by the baby unit. The other 
one is to show the volume level during 
speaker volume setting.

   One to three green 

lights indicate a moderate sound level 
detected by the baby unit.

   Additional red 

lights indicate a higher sound level 
detected by the baby unit (e.g. baby 
crying loudly).

   One to three green 

lights indicate Level 1 to Level 3 of the 
speaker volume setting.

   Additional red 

lights indicate Level 4 to Level 5 of 
the speaker volume setting.

Ć

Ć

Ć

Ć

3

4

Press to enter the menu while idle.

While in a menu, press to choose an 
item, or save a setting.

While in a menu, press to return to 
the previous menu.
Press to return idle while current 
menu is already in root level.

Press to increase the speaker volume.
While in a menu, press to scroll up.

Press to decrease the speaker 
volume.
While in a menu, press to scroll down.

Ć

Ć

Ć

Ć

Ć
Ć

Ć

Ć

5

Light on when the parent unit battery is 
being charged.
Light flashes when the parent unit 
battery is low and needs charging.
Light off when the parent unit battery 
is fully charged, or when no battery is 
installed.

Ć

Ć

Ć

6

Press to power on.
Press and hold to power off.
Press to turn on or off the screen. 

Ć
Ć
Ć

7

Press and hold to talk to the selected 
baby unit; release to stop talking. 
While in a menu, press to return idle.

Ć

Ć

8

9

10

11

1 set for DM222;
2 sets for DM222-2

NOTES

Use only the parent unit power adapter or the baby 
unit power adapter supplied with this product.

Make sure the electrical outlets are not controlled 
by wall switches.

The parent unit power adapter and baby unit power 
adapter are intended to be correctly oriented in a 
vertical or floor mount position. The prongs are not 
designed to hold the plug in place if it is plugged into 
a ceiling, under-the-table or cabinet outlet.

Make sure the parent unit, the baby unit and the 
power adapter cord are out of reach of children.

Ć

Ć

Ć

Ć

 displays when strong signal 

strength is detected between the 
baby unit and the parent unit.

 displays when moderate signal 

strength is detected between the 
baby unit and the parent unit.

 displays when the weak link 

signal strength is detected between 
the baby unit and the parent unit.

 displays when the link between 

the baby unit and the parent unit is 
lost.

Ć

Ć

Ć

Ć

Displays when the projector of the 
baby unit is on.

Ć

Displays when the sound alert of 
the parent unit is turned on.
Flashes when there are sounds 
detected from the baby unit at 
which the speaker volume is turned 
off.

Ć

Ć

Displays when the vibration alert of 
the parent unit is turned on.

Ć

Displays when the volume is turned 
off.

Ć

 animates when 

the battery is charging.

 displays solid when the battery 

is fully charged.

 flashes when the battery fails to 

charge.

 displays when battery is in low 

level and needs charging.
No battery icon displays when there 
is no battery installed.

Ć

Ć

Ć

Ć

Ć

Press power on to turn on the baby unit. The 

 lights up

.

Press and hold power on again to power off 
the baby unit. The 

turns off.

Press   to power on the parent unit. The 
screen turns on.
Press and hold

 again to power off the 

parent unit. The screen turns off.

Press volume + or volume - on the baby 
unit at any time.

You can adjust the speaker volume from 
VOLUME 1 to VOLUME 5, or turn it off. The 
speaker volume is preset to VOLUME 3.

Press volume + or volume - on the parent 
unit while viewing image from baby unit.

When the speaker volume is set to off, the 
screen displays 

.

You can use the parent unit to change the sound 
sensitivity level of the baby unit from LEVEL 1
to LEVEL 5. The higher the sound sensitivity 
level is set, the more sensitive the baby unit is in 
detecting sounds for transmitting to the parent 
units. The sensitivity level is preset to LEVEL 5.
If you want the baby unit to be very sensitive in 
detecting sounds, you may set the sensitivity 
level to the highest level (LEVEL 5), so that 
the baby unit will always detect any sounds 
including background noises for transmitting to 
the parent units. If you want the baby unit to be 
less sensitive in detecting sounds, you may set 
the sensitivity level to a lower level (LEVEL 1
to LEVEL 4), so that the baby unit will transmit 
sounds to the parent units only when your baby is 
very noisy or crying loudly.

Press menu when the parent unit is not in 
use.
Press select.

Press volume + or volume - to choose the 
sensitivity level.

Ć

Ć

Ć

Ć

Ć

Ć

1.

2.

3.

      -OR-
      

When you choose NO, press select to confirm 

your selection. The screen displays the previous 
menu.

NOTE

When you reset the default settings, any units that 
are turned off or out of range will not be reset.

You can broadcast messages from a parent unit to 
the baby unit and the other parent unit. If you have 
two parent units, you can use both of them at the 
same time to talk to the baby unit.

Press and hold talk on the side of the parent 
unit. The screen displays TALK when the 
voice connection to the baby unit is made. 
Speak towards the mic on the parent unit. 
Your voice is broadcast to the baby unit and 
the other parent unit.

NOTE

When a parent unit is talking to the baby unit, it is 
also broadcast to the other parent unit. However, 
any sounds from the baby unit cannot be 
transmitted to the parent units at the same time.

Use this feature to find misplaced parent units.

Press page on the baby unit. All idle parent 
units ring and display PAGING.
To end paging, press any key on the parent 
unit, or press PAGE on the baby unit.

NOTES

Paging rings all parent units even if the speaker 
volume of parent unit is set to VOLUME OFF.
The baby unit cannot page any parent unit that is 
turned off, out of range or talking to the baby unit.

Ć

Ć

Ć

1.

2.

Ć

Ć

You can turn on the projector on the baby unit to 
play lullaby, and form some interesting and colour 
images at the same time.

When the projector is turned on,  displays. The 
default setting is preset to NO.

Press 

 to play lullaby. The interesting and 

colour images appear at the same time.
Press 

 again to stop playing the lullaby.

Press 

for a third time to turn off the 

projector. The interesting and colour images 
disappears.

NOTE

If the baby unit receives talkback from the parent 
unit during lullaby playback, the lullaby playback 
will be paused, and resumes after the talkback 
finishes.

You can select a language (English, French or 
Spanish) to be used in all screen displays. The 
language is preset to English.

Press menu when the parent unit is not in 
use.

Press volume + or volume - to choose 
Language 

( LANGUE if French is set, or 

 if Spanish is set ), then press 

.

Press volume + or volume - to choose 
ENGLISH

, FRANCAIS or ESPANOL.

Press select to confirm your selection. The 
screen display SAVED and you hear a 
confirmation tone.

NOTE

The language setting on each parent unit is 
independent.

Use this feature to restore to the default settings. 
Restoring the default settings on one parent unit 
will also reset the shared settings for sensitivity of 
the other parent unit.

Press menu when the parent unit is not in 
use.

Press volume + or volume - to choose SET 
DEFAULT

, then press select.

Press volume + or volume - to choose YES
or NO.
When you choose YES, press select to 
confirm your selection. You hear a confirmation 
tone and then the screen displays LINKED.

Ć

Ć
Ć

Ć

1.

2.

3.

4.

Ć

1.

2.

3.

4.

on purchasing your new VTech product. Before 
using this product, please read 
Important safety instructions

.

For support, shopping, and everything new at 
VTech, visit our website at 
www.vtechphones.com

.

Register your product online for 
enhanced warranty support.

Learn about the latest VTech 
products.

NOTE

This baby monitor is intended as an aid. It is not a 
substitute for proper adult supervision, and should not be 
used as such.

CAUTION

Keep the baby unit out of the reach of the baby. Never 
place or mount the baby unit inside the baby’s crib or 
playpen.

Place the baby unit at least 1 meter / 3 feet 
away from your baby.

NOTE

If you experience audio feedback on either the parent 
unit or baby unit, move the parent unit further away until 
there is no more audio feedback; or press volume - on 
the parent unit to lower the audio feedback sound.

2.

Place the parent unit at least 1 meter / 3 
feet away from the baby unit.

TIP

You can increase the speaker volume of the parent unit 
if you cannot hear the sounds transmitted from the baby 
unit.

The operating range of the baby monitor is up to 
300 meters (1,000 feet) outdoors or 50 meters 
(160 feet) indoors. The actual operating range 
may vary depending on the environmental 
conditions, and other interferences such as 
walls, doors, and other obstructions. 

1.

LINKED

When the link between the 
parent unit and the baby unit is 
established.

LOW 
BATTERY

The parent unit uses only the 
rechargeable battery pack and it 
needs to be recharged.

NOT 
LINKED

When the link between the parent 
unit and the baby unit is lost 
continuously for over 10 seconds.

PAGING

All idle parent units are being 
paged by the baby unit.

SAVED

Your selection has been saved.

SEARCHING

The parent unit is out of range of 
the baby unit, or the baby unit is 
out of power.

TALK

The parent unit is talking to the 
baby unit.

TALKBACK

The other parent unit is talking to 
the baby unit.

At least 1 meter (3 feet)

At least 1 meter

(3 feet)

b

a

c
d

e

f

b

e

a

c

d

k

i

j

h

f

g

THIS SIDE UP