Rosslare Enterprises Ltd KE-30G Manuale Utente
KE-30
Installation Instructions
Battery Operated Two-Way Wireless Keypad
1
0706-0960254+00
1. Introduction
The KE-30 is a wireless keypad for use with Rosslare wireless
panels. The KE-30 features include:
•
Fully featured keypad, including: LED indicators, function
buttons (arm-away, arm-home, disarm), numeric pad,
buzzer, and emergency triggering.
•
RFID proximity reader for arming and disarming; The range
varies according to the type of card used, and is up to a
maximum of 2.5 cm.
•
LED indications of the system status, including: Alarm In
Memory, Trouble and Bypass, and system status (armed
away / armed home / disarmed).
•
Wall keypad tamper-protection mechanism.
•
Low-power consumption; its internal batteries are
designed to last for years, under normal operation.
Figure 1: KE-30 Wireless Keypad
2. Technical Specifications
2.1 Electrical Characteristics
Power Supply Voltage: 4 batteries - CR123A 3V 1300mAh
Current Consumption: Standby - 17 uA ; Transmit 14 mA
Battery life – 1 year
Current Consumption: Standby - 17 uA ; Transmit 14 mA
Battery life – 1 year
2.2 Environmental Characteristics
Operating Environment: Indoor use
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Operating Humidity: 0 to 95% (Non-Condensing)
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Operating Humidity: 0 to 95% (Non-Condensing)
2.3 Physical Characteristics
Dimensions HxWxD: 140x100x28 mm (5.51x3.94x1.10 inch)
Weight: 99g (0.218lb)
RFID Proximity Reader: Read-compatible with Wiegand 26-bit
Weight: 99g (0.218lb)
RFID Proximity Reader: Read-compatible with Wiegand 26-bit
EM4102 card (or compatible standard)
Read range: Maximum of 2.5 cm (using Rosslare's AT-R14)
Frequencies: G-Band (433.92 MHz), H-Band (868.35 MHz)
Frequencies: G-Band (433.92 MHz), H-Band (868.35 MHz)
3. Install the KE-30
3.1 Mounting the KE-30
Open the KE-30 and mount the back cover of the KE-30 flush
to the wall.
To mount the keypad on the wall:
1. Locate and release the screws at the bottom of the
To mount the keypad on the wall:
1. Locate and release the screws at the bottom of the
keypad, and open the cover.
2. Place the back plate at the desired location. (The keypad
should be installed at eye level.)
3. Use the dimensions given in the figure to the right, or use
the back cover as a template.
4. Drill four holes in the wall and insert the anchors provided.
5. Mount and fasten the back plate with the screws
provided, and assure that the back plate is level.
6. Secure the back plate with the screws referred to in
Step 1.
Figure 2: Mounting Dimensions
3.2 Replacing the Batteries
To replace the CR123A batteries:
1. Remove the used batteries and replace them .
1. Remove the used batteries and replace them .
2. Close the cover and the system is up and running.
3.3 Enrolling the Keypad
Please refer to the Keypad Enrolling section of the HomeLogiX
wireless panel manual or refer to any Rosslare wireless panel
manual that supports the relevant keypad.
3.4 Enrolling Proximity Cards
Please refer to the Proximity Card Enrolling section of the
HomeLogiX wireless panel manual or refer to any Rosslare
wireless panel manual that supports the relevant proximity
cards.
Figure 3: Battery Placement