Seiko Epson Corporation AP013 Manuale Utente
TREUM
Sensor solor GPS watch
Sensor solor GPS watch
Use for EPSON sensor solar GPS Watch “TREUM
This GPS watch comes with a dedicated sensor.
This GPS watch comes with a dedicated sensor.
When you start to use the product, Please read the TREUM Users
Manual page at “Preparing to Measure expanded sensor
Manual page at “Preparing to Measure expanded sensor
Manufacture by SEIKO EPSON CORPORATION
Address: 3‐5, Owa 3‐chome, Suwa‐shi , Nagano‐ken 392‐8502
Japan
Address: 3‐5, Owa 3‐chome, Suwa‐shi , Nagano‐ken 392‐8502
Japan
http://www.epson.com
Importer/Contact：Epson America , Inc.
Address: 3840 Kilroy Airport Way Long Beach, CA 90806 U.S.A
Address: 3840 Kilroy Airport Way Long Beach, CA 90806 U.S.A
http://www.epson.com/cgi‐bin/Store/jsp/index.do
CAUTION：Risk of explosion if battery is replaced by an incorrect type.
CAUTION：Dispose of used batteries according to the instructions
CAUTION：Dispose of used batteries according to the instructions
.
Model:TR‐MB8
FCC ID : BKMAP012
IC: 1052E‐AP00１
IC: 1052E‐AP00１
FCC /IC Notices
This transmitter must not be co‐located or operated in
conjunction with any other antenna or transmitter
This transmitter must not be co‐located or operated in
conjunction with any other antenna or transmitter
This device complies with part 15 of FCC Rules and Industry Canada’s licence‐exempt
RSSs. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des
CNR d‘Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l‘appareil ne doit pas
produire de brouillage, et (2) l’appareil doit accepter tout brouillage subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
CNR d‘Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l‘appareil ne doit pas
produire de brouillage, et (2) l’appareil doit accepter tout brouillage subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Caution:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
**Explanation that an SAR examination is unnecessary with Portable
equipment**
equipment**
This equipment complies with FCC/IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF)
Exposure Guidelines and RSS‐102 of the IC radio frequency (RF) Exposure
rules. This equipment has very low levels of RF energy that are deemed to
comply without testing of specific absorption ratio (SAR).
an uncontrolled environment and meets the FCC radio frequency (RF)
Exposure Guidelines and RSS‐102 of the IC radio frequency (RF) Exposure
rules. This equipment has very low levels of RF energy that are deemed to
comply without testing of specific absorption ratio (SAR).
Cet équipement est conforme aux limites d’exposition aux rayonnements
énoncées pour un environnement non contrôlé et respecte les règles les
radioélectriques (RF) de la FCC lignes directrices d'exposition et
d’exposition aux fréquences radioélectriques (RF) CNR‐102 de l’IC. Cet
équipement émet une énergie RF très faible qui est considérée conforme
sans évaluation du débit d’absorption spécifique (DAS).
énoncées pour un environnement non contrôlé et respecte les règles les
radioélectriques (RF) de la FCC lignes directrices d'exposition et
d’exposition aux fréquences radioélectriques (RF) CNR‐102 de l’IC. Cet
équipement émet une énergie RF très faible qui est considérée conforme
sans évaluation du débit d’absorption spécifique (DAS).
**Explanation of the EMC demand part of the United States. **
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However,there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However,there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Model:MB00
FCC ID : BKMAP013
IC: 1052E‐AP002
IC: 1052E‐AP002
※
dedicated sensor
Certification information