Honeywell International Inc. 8DL5800TM-1 Manuale Utente
ADEMCO 5800TM
TRANSMITTER MODULE
Used with Bidirectional Wireless Devices
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The 5800TM Transmitter Module is designed to be used in conjunction with one or more wireless
bidirectional devices. The 5800TM is compatible with any control panel that is also equipped with a
5800 Series RF receiver. It complements the RF receiver in that it transmits the information to be
displayed on, or sounded by a wireless bidirectional keypad. No modification to the control panel is
necessary. Connections are made directly to the control panel’s keypad connection points, as
described below. See the installation instructions that accompany the 5800 Series wireless
bidirectional keypad for complete operating information for the 5800TM/keypadcombination.
INSTALLATION
Observe the same precautions in selecting a location for the 5800TM as for the system’s RF
receiver, to insure good transmission and reception. The 5800TM must be located next to the
system’s receiver (between one and two feet from the receiver’s antennas).
Do not install the 5800TM within the system control panel cabinet; mount it remotely, on its
accompanying mounting bracket. The bracket is easily installable via two countersunk mounting
holes. Keyhole slots on the rear of the 5800TM slip onto two hooks on the mounting bracket.
PROGRAMMING For an Addressable System:
1. Select one of the following addresses for the 5800TM by removing its cover, and cutting the
appropriate
jumper(s) on its circuit board, as follows:
2. Program the control panel, by assigning the address selected above to one of the wired consoles
in the
system.
FOR ADDRESS
TRANSMITTER MODULE
Used with Bidirectional Wireless Devices
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The 5800TM Transmitter Module is designed to be used in conjunction with one or more wireless
bidirectional devices. The 5800TM is compatible with any control panel that is also equipped with a
5800 Series RF receiver. It complements the RF receiver in that it transmits the information to be
displayed on, or sounded by a wireless bidirectional keypad. No modification to the control panel is
necessary. Connections are made directly to the control panel’s keypad connection points, as
described below. See the installation instructions that accompany the 5800 Series wireless
bidirectional keypad for complete operating information for the 5800TM/keypadcombination.
INSTALLATION
Observe the same precautions in selecting a location for the 5800TM as for the system’s RF
receiver, to insure good transmission and reception. The 5800TM must be located next to the
system’s receiver (between one and two feet from the receiver’s antennas).
Do not install the 5800TM within the system control panel cabinet; mount it remotely, on its
accompanying mounting bracket. The bracket is easily installable via two countersunk mounting
holes. Keyhole slots on the rear of the 5800TM slip onto two hooks on the mounting bracket.
PROGRAMMING For an Addressable System:
1. Select one of the following addresses for the 5800TM by removing its cover, and cutting the
appropriate
jumper(s) on its circuit board, as follows:
2. Program the control panel, by assigning the address selected above to one of the wired consoles
in the
system.
FOR ADDRESS
CUT
JUMPER(S)
JUMPER(S)
28
RED (W 1)
29
WHITE (W 2)
30
BOTH
Note: For those controls requiring device programming (in ✱93 mode), program this device as an
“Alpha Console.”
For a Non-Addressable System: No programming is required.
WIRING CONNECTIONS Connect the 5800TM to the control panel’s remote keypad connection
points, using the supplied connector with flying leads. Wire colors and functions match those for
keypads:
RED +12VDC (Aux Power)
GREEN: Data to Control Panel
YELLOW : Data from Control Panel
BLACK: Ground (–)
BLUE: Not used
SPECIFICATIONS
Physical: 2-1/4”W x 4-1/8”H x 7/8”D (57mm x 105mm x 22mm)
Electrical: Voltage: +12VDC (from control panel remote keypad connection points) Current: 20mA