Honeywell International Inc. 8DL5804AP Manuale Utente
function and symbol printed on it, as well as
an adhesive back for easy pasting.
To paste a label on a button, slowly peel
off a label with a selected function and paste
it on the button of the transmitter. If you
decide later to reprogram a button, the label
can be easily removed or a new label pasted
over the existing one.
Additional colored buttons (red and blue) are
also provided which can be used with or
without the labels. The buttons can be
inserted only in the areas provided for them
(see Figure 3).
To insert the colored buttons, do the
following:
an adhesive back for easy pasting.
To paste a label on a button, slowly peel
off a label with a selected function and paste
it on the button of the transmitter. If you
decide later to reprogram a button, the label
can be easily removed or a new label pasted
over the existing one.
Additional colored buttons (red and blue) are
also provided which can be used with or
without the labels. The buttons can be
inserted only in the areas provided for them
(see Figure 3).
To insert the colored buttons, do the
following:
1. Holding the transmitter with the buttons
face down, remove the case back by using
the blade of a small screwdriver to pry it
open (see Figure 2).
the blade of a small screwdriver to pry it
open (see Figure 2).
2. Carefully remove the PC board by its
rubber casing, making sure the board
does not come out of the casing. Do not
bend the exposed battery tabs on the PC
board.
does not come out of the casing. Do not
bend the exposed battery tabs on the PC
board.
3. Replace the desired buttons, either red or
blue, in each button's designated opening
(see Figure 3).
(see Figure 3).
4. When finished, replace the PC board,
making sure the button tabs on the board
face the four buttons, and snap the case
front and back together.
face the four buttons, and snap the case
front and back together.
After inserting the new buttons, you may
wish to check the 5804AP for proper
operation.
wish to check the 5804AP for proper
operation.
Battery Tabs Shown
Figure 2: Battery tabs shown.
Blue
Red
Figure 3: 5804AP shown open,
buttons facing down.
SPECIFICATIONS
Transmission Frequency: 315 MHz
Unit Dimensions:
57mm x 38mm x 12.7mm
57mm x 38mm x 12.7mm
+ POS. end
must face down
must face down
+ POS. end
must face down
must face down
BATTERY ACCESS
Battery:
Maxell CR2025, Duracell DL 2025 or Varta
CR2025
Maxell CR2025, Duracell DL 2025 or Varta
CR2025
Battery Access:
Remove case back by using the blade of a
small screwdriver to pry open. Place
batteries in case back locations (see Figure
4).
Remove case back by using the blade of a
small screwdriver to pry open. Place
batteries in case back locations (see Figure
4).
+ POS END MUST FACE DOWN.
To close, snap case front and back together.
Important Note: Do not remove Printed
Circuit Board.
To close, snap case front and back together.
Important Note: Do not remove Printed
Circuit Board.
FCC ID: CFS8DL5804AP
PART 15 STATEMENT
THIS DEVICE COMPLIES WITH PART
15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY
NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE
MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL WITH
WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION, AND FOR DETAILS
REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION, AND FOR DETAILS
REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
Honeywell International Inc.
165 Eileen Way, Syosset, New York 11791
Copyright ©
2005 Honeywell International Inc. N7674-3 4/05 PRELIMINARY