Honeywell International Inc. 8DL5804BDMX Manuale Utente
INSTALLATION INSTRUCTIONS
GENERAL INFORMATION
The 5804BD is a four-button wireless key that permits an alarm system to be controlled remotely. It is a bi-
directional device, which means that it can send a command to the control, such as to arm or disarm, and can also
receive status back from the control, which is indicated by two bi-color status LEDs and a piezoelectric sounder.
Each button can be programmed for any zone response type by using the control’s transmitter “learn” mode. Typical
use is for arming, disarming, panic, and output relay operation.
directional device, which means that it can send a command to the control, such as to arm or disarm, and can also
receive status back from the control, which is indicated by two bi-color status LEDs and a piezoelectric sounder.
Each button can be programmed for any zone response type by using the control’s transmitter “learn” mode. Typical
use is for arming, disarming, panic, and output relay operation.
The 5804BD must be used in conjunction with a 5800TM (Transmitter Module) and 5881 RF Receiver.
The unit is powered by two replaceable Lithium batteries designed to provide up to two years of life (see “To
Replace the Battery” for more information).
Replace the Battery” for more information).
PROGRAMMING THE 5804BD HOUSE ID
You need to program a House ID number into the unit before you can to use it to display the system status.
The
House ID number must be same as the one used in the control panel.
The House ID must be in the range of
01 to 31. The default in the 5804BD is 10.
To Enter a House ID
1. Enter House ID mode by pressing the “
A
,” “
B
,” and “
C
” buttons at the same time until the Red and Green
LEDs alternate flashing.
2. Enter the House ID number by using the “
A
” button to enter the 10’s digit and the “
B
” button to enter the 1’s
digit.
Note:
If the entry is out of range (greater than 31), the unit will generate a long beep and discard the
entry.
3. Accept the entry by pressing the “
D
” button.
4. The unit displays the stored number by flashing the left LED for the 10’s
digit and flashing the right LED for the
1’s digit (for example, for House ID 21, the left LED will flash twice, the right LED will flash once).
5. The unit will then exit the House ID mode (a beep will be heard).
Example:
To enter House ID # 17 into the unit:
To View the House ID
a)
Enter House ID mode as described in step 1 (above).
b)
Depress the “
D
” button to view.
c)
The unit will display the stored number as described in step 4 (above).
d)
The unit will then exit House ID mode (a beep will be heard).
5804BD
BI-DIRECTIONAL WIRELESS KEY
N8209 01/97
Loop Assignments:
•
Button A =>Loop 3
•
Button B =>Loop 2
•
Button C =>Loop 4
•
Button D =>Loop 1
Note
: Place the 5881 receiver and the
5800TM transmitter module in a high,
centrally located area for best reception.
The 5800TM module must be located
between 1 and 2 feet from the receiver.
centrally located area for best reception.
The 5800TM module must be located
between 1 and 2 feet from the receiver.
Enter HID mode:
Press A + B + C
buttons until LEDs
flash
Press A + B + C
buttons until LEDs
flash
.
Enter HID # 17: Press
& release A button
once, press & release
B button 7 times
& release A button
once, press & release
B button 7 times
.
To accept entry, press
D button
D button
.
1
2
3
4
HID will be shown
by flashing LEDs.
Then exit HID
mode.
by flashing LEDs.
Then exit HID
mode.