Honeywell International Inc. 8DL5827BD-1 Manuale Utente
- 2 -
3. Affix the appropriate panic key label to the space below any panic key that is active, according to the function that has been
programmed for it in the control. A sheet of labels accompanies the 5827BD.
Note: Not all of the three panic keys may be active for the system with which the console is used. This depends on the type of
control used and its programming. Refer to the control’s installation manual.
control used and its programming. Refer to the control’s installation manual.
4. Connect the provided antenna, if necessary, by screwing it into its threaded connector at the top of the console. The 5827 has
an internal antenna, and in many installations the system will operate adequately with this antenna alone. For large installations,
however, it may be necessary to add the external antenna.
however, it may be necessary to add the external antenna.
5800TM Transmitter Module Installation
Installation instructions accompany the 5800TM, but are given here as well, for your convenience.
Observe the same precautions in selecting a location for the 5800TM as for the system’s 4281 or 5881 RF receiver, to insure good
transmission and reception. The 5800TM must be located next to the system’s receiver (between one and two feet from the
4281/5881’s antennas). Do not install the 5800TM within the system control panel’s cabinet. Mount it remotely, on its accompanying
mounting bracket. The bracket is identical to the one that accompanies the 5827BD and may be mounted the same way.
Installation instructions accompany the 5800TM, but are given here as well, for your convenience.
Observe the same precautions in selecting a location for the 5800TM as for the system’s 4281 or 5881 RF receiver, to insure good
transmission and reception. The 5800TM must be located next to the system’s receiver (between one and two feet from the
4281/5881’s antennas). Do not install the 5800TM within the system control panel’s cabinet. Mount it remotely, on its accompanying
mounting bracket. The bracket is identical to the one that accompanies the 5827BD and may be mounted the same way.
PROGRAMMING
For an addressable system:
1. Select on e of the following addresses for the 5800tm by removing its cover, and cutting the appropriate jumper(s) on its
1. Select on e of the following addresses for the 5800tm by removing its cover, and cutting the appropriate jumper(s) on its
circuit board, as follows:
FOR ADDRESS
CUT JUMPER(S)
28 RED
(W1)
29 WHITE
(W2)
30 BOTH
2. Program the control panel, by assigning the address selected above to one of the wired consoles in the system.
For a Non-Addressable System: No programming is required.
WIRING CONNECTIONS
Connect the 5800TM to the control panel’s connection points, using the supplied connector with flying leads. Wire colors and
functions match those for consoles:
functions match those for consoles:
RED +12VDC
BLACK Ground
GREEN
Data to Control Panel
YELLOW
Data from Control Panel
BLUE
Not used
OPERATION
Power-up and System Status Inquiry
Power-up and System Status Inquiry
Touching the [
✱] ([ON/STAT]) key powers up the 5827BD, and sends an inquiry to the 5800TM, requesting the system status to be
annunciated (see table on next page). Subsequent depressions of the same key will initiate additional inquiries.
Notes: 1. Upon power-up (by depression of the [ON/STAT] key), the yellow LED will blink. The yellow LED will be lit during RF
communication, indicating transmission is in progress or reception has just been completed. If a low battery condition exists
in the 5827BD, it will be displayed on wired consoles as zone 00.
in the 5827BD, it will be displayed on wired consoles as zone 00.
2. At any time (following a power-up), the depression of any key and its acceptance by the console will be indicated by a blink
of the yellow LED, and a brief key actuation ‘blip’ will be heard. (As explained later, a panic key has to be continuously
depressed for at least 2 seconds in order to power-up and/or be accepted by the system).
depressed for at least 2 seconds in order to power-up and/or be accepted by the system).
3. A long (2 second) beep, occurring within 4 seconds after power-up or following the last key depression (of a command or an
inquiry) indicates lack of response from the control (via the 5800TM). Press the [ON/STAT] key again (or move to a new
location and re-key your command).
location and re-key your command).
Approximately 10 seconds after the last key depression, the 5827BD will automatically power down.
No subsequent LED or sound indications will occur until the unit is again powered up (thus, in chime mode, the chime is not
annunciated by the 5827BD).
No subsequent LED or sound indications will occur until the unit is again powered up (thus, in chime mode, the chime is not
annunciated by the 5827BD).
The following table shows the various status indications that can occur during the time that the unit is powered up:
SYSTEM STATUS INDICATIONS for 5827BD
LED
LED
CONDITION
CONSOLE’S SOUNDER
SYSTEM STATUS
1
2 BEEPS
2
ARMED AWAY OR MAXIMUM
ON
STEADILY
3 BEEPS
2
ARMED STAY OR INSTANT
PULSED BEEPING
3
ARMED, FIRE ALARM IN PROGRESS, OR MEMORY
OF IT IS PRESENT
OF IT IS PRESENT
STEADY SOUND
3
ARMED, BURGLARY IN PROGRESS, OR MEMORY
OF IT IS PRESENT
OF IT IS PRESENT
RED
(ARM)
BLINKING
SILENT
DISARMED, BUT NOT YET CLEARED OF ALARM
MEMORY HISTORY (BURGLARY OR FIRE)
MEMORY HISTORY (BURGLARY OR FIRE)