Honeywell International Inc. 8DL6150RF-3 Manuale Utente

Pagina di 2
 
PREK4460-1V5  8/05 Rev A 
 
 
 ADEMCO 6150RF
ADEMCO 6150RF
ADEMCO 6150RF
ADEMCO 6150RF    
Keypad/Transceiver
Keypad/Transceiver
Keypad/Transceiver
Keypad/Transceiver 
INSTALLATION AND SETUP GUIDE 
GENERAL INFORMATION 
The 6150RF Keypad/Transceiver is a combination unit incorp-
orating a normally-open relay output and the functions of: 
•  6150 Fixed Addressable Keypad 
•  5881M RF Receiver 
•  5800TM Transmitter Module 
The 6150RF Keypad/Transceiver may be used on any control 
panel that supports the 6150 Keypad (e.g., VISTA-10P/10SE, 
VISTA-15/15P, VISTA-20P/20SE/20HWSE, VISTA-40, VISTA-
50P, VISTA-128B/128BP, 4110DL, 4110XM, 4140XMP)  
Wireless Features 
The 6150RF supports the following: 
•  5828/5828V wireless keypads. 
•  Up to 8 wireless keys locally (programmed directly into 
6150RF) without occupying any zones supported by the 
control panel. 
•  Button-type transmitters (e.g., 5804, 5804BD) for local 
operation. 
•  A maximum of 16 transmitters programmed into any 5800 
Series-supported control panel. 
•  Wireless keys with high-security (e.g., 5804E). 
•  RF jam detection when the receiver is enabled. 
The 6150 provides the following: 
•  Low-battery indications for the local wireless keys. 
•  A nominal range of 200' for the RF transmitters (some 
transmitters have a shorter range). 
•  Wireless key support for control panels that do not support 
RF themselves (such as 4110DL). 
U
U
U
ULLLL 
The 5802, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 
5804WATCH, 5805BDV, 5814, 5816TEMP, 5819, 5819SBRS, 
5819SWHS, and 5850 transmitters are not intended for UL 
installations. 
Programming Features 
•  Auto Enroll mode for programming wireless keys. 
•  Provides a method for deleting a serial number and re-
enrolling a new one in its place. 
•  Provides default settings for the wireless key functions. 
Additional Features 
•  Sends status signals (Armed, Ready, etc.) to bi-directional 
units such as 5804BDV, 5805BDV and 5828/5828V. 
•  Operates the on-board relay in conjunction with the receiver 
(e.g., to trip a garage door opener).  
Note: This particular feature is not intended for UL installations. 
•  Activates relays programmed into the control panel. 
•  Provides an End User mode to enable/disable local wireless 
keys (e.g., if a user accidentally loses a wireless key). (Refer 
to the 6150RF User Guide for this procedure.) 
APPLICATION GUIDELINES  
Use the following guidelines when planning an installation: 
•  Local wireless keys (wireless keys programmed directly into 
the 6150RF) may be used regardless of whether the RF 
receiver in the 6150RF is enabled or disabled. 
•  If using bi-directional devices, be sure to enable the 
transmitter module in the 6150RF. 
•  If transmitters are programmed into the control panel, be 
sure to enable the receiver. (Make sure you do not exceed 
the number of receivers supported by the control panel.) 
•  If a local wireless key is programmed to arm/disarm or to 
trigger a relay on the control panel, a user code must be 
entered into the 6150RF. This user code must also be 
programmed into the control panel. 
•  You must set the House ID only if you are using RF keypads 
and/or bi-directional devices; AND the House ID Source is 
the 6150RF (Local). 
6150RF Application Guide 
The following guide outlines how to program the wireless keys, RF receiver, and the House ID in the 6150RF for your installation. 
*  Two 6150RFs are needed for this application: one assigned to partition 1 and one assigned to partition 2. 
**  If using an RF keypad on only one partition, the 6150RF’s partition assignment must match the partition set in field 1*48. 
***  If set for Local on a partition control, the 6150RF’s partition assignment must match the one programmed in the BD device. 
Are you using 
6150RF Programming Options 
System Control Panel 
RF keys 
beyond 
system’s 
capacity? 
RF receivers 
beyond 
system’s 
capacity? 
RF keypads and/or Bi-
directional devices on 
more than 1 partition? 
Program 
Wireless Keys 
Into 
Receiver 
Enable 
House ID 
Source*** 
4110DL, 4110XM, 4140XMP, VISTA-
20HWSE 
N/A 
N/A 
N/A 
6150RF 
OFF  
Local [0] 
NO 
NO 
N/A 
System 
ON [1] 
System [1] 
YES 
NO 
N/A 
6150RF 
ON [1] 
System [1] 
VISTA-10P, VISTA-10SE, VISTA-15, 
VISTA-15P, VIA-30PSE 
YES 
YES 
N/A 
6150RF 
OFF [0] 
Local [0] 
NO 
NO 
NO 
System 
ON [1] 
System [1] 
YES 
NO 
NO 
6150RF 
ON [1] 
System [1] 
YES 
YES 
NO 
6150RF 
OFF [0] 
Local [0] 
NO 
YES 
YES* 
System 
OFF [0] 
Local [0] 
VISTA-20SE, VISTA-20P 
YES 
YES 
YES* 
6150RF 
OFF [0] 
Local [0] 
NO 
NO 
NO** 
System 
ON [1] 
System [1] 
YES 
NO 
NO** 
6150RF 
ON [1] 
System [1] 
YES 
YES 
NO** 
6150RF 
OFF [0] 
Local [0] 
NO 
YES 
YES 
System 
OFF [0] 
Local [0] 
VISTA-40, VISTA-50P, VISTA-128B, 
VISTA-128BP 
YES 
YES 
YES 
6150RF 
OFF [0] 
Local [0] 
SEE THE NEXT   PAGE
FOR THE FCC INFO.