ademco 8DL6152RF Manuale Utente
ADEMCO 6152RF Keypad / Transceiver – Installation and Setup Guide
Fixed Addressable Keypad/Transceivers for use with Honeywell Control Panels; incorporates normally-open
relay output with the functions of a medium 16 zone RF Receiver and a 5800 Transmitter module.
relay output with the functions of a medium 16 zone RF Receiver and a 5800 Transmitter module.
= READY to Arm
= NOT READY to Arm
= System ARMED
= System NOT ARMED
Programmable Function Keys
Arming Keys
6152RF: Fixed Word Display
2-Digit Zone Identifier
2-Digit Zone Identifier
The ‘21’ digits are used for specific
trouble indications. Refer to the
control panel instructions for details.
trouble indications. Refer to the
control panel instructions for details.
ALARM
FIRE
FIRE
AWAY
BYPASS
STAY
CHECK
INSTANT
CANCELED
NO
NIGHT
AC
NOT READY
CHIME BAT
CHIME BAT
TEST
PHONE
6152RF-KEYPAD-LBLD-032613
Sounder
Wall
Surface
Surface
2
1
SEE Detail
A
Optional Front Cover Securing Screw
(Required in European Installations)
(Required in European Installations)
Install Four (4)
Mounting Screws
Mounting Screws
Control Panel
1. OPEN
Keypad
Front
Cover
Front
Cover
2. WIRE
3. MOUNT
• Connect only one wire per terminal.
• For Daisy-Chain Configurations, use
wire splicing so only one wire is
connected to each terminal.
• For Daisy-Chain Configurations, use
wire splicing so only one wire is
connected to each terminal.
Mount on drywall, or in a single
or double-gang electrical box.
or double-gang electrical box.
AUX
RELAY OUTPUT
CONNECTIONS
CONNECTIONS
[ ] GROUND
[Y] DATA IN
[+] +12VDC IN
[G] DATA OUT
Yellow
Black
Red
Red
Green
CONTROL PANEL
TERMINAL STRIP
16-24 AWG Only
KEYPAD
NO
C
DATA
IN
DATA
OUT
AUX
Detail
A
G
Y
To activate Function keys,
press and hold key for at
least 2 seconds; key pairs
are activated immediately.
press and hold key for at
least 2 seconds; key pairs
are activated immediately.
Table 1 – Programmable
Function Keys
Function Keys
A or
and
B or
and
C or
and
D
Note: See the control’s instructions for
details on programming the Function
keys for panic alarms or other special
functions (i.e., macros).
details on programming the Function
keys for panic alarms or other special
functions (i.e., macros).
Programmable to support the
following :
following :
-
Bi-directional 5828/5828V
wireless keypads and wireless
keys (e.g., 5804BDV, 5834-4,
etc.)
keys (e.g., 5804BDV, 5834-4,
etc.)
-
Up to eight button-type wireless
keys locally (programmed
directly into the keypad),
without occupying control panel
zones
directly into the keypad),
without occupying control panel
zones
-
Up to 16 5800 series wireless
zones programmed into any
supported control panel
supported control panel
-
Wireless keys with high security
mode enabled
Table 3 – Icon Descriptions
ICON DESCRIPTION
TEST SYSTEM
BYPASS ZONES
BYPASS ZONES
ASSIGN CODES
CHIME MODE
CHIME MODE
ARM MAXIMUM
ARM INSTANT
ARM AWAY
ARM NIGHT STAY
DISARM
ARM STAY
SETTINGS
Table 2 – Settings Key
Settings Key
Result
Press
for 2 Seconds
Enters Display Test Mode
Press
for 2 Seconds
and during the Display Test,
press and hold
and
for 3 Seconds
Reboots the Keypad (the
keypad beeps and the ARM
and READY LED’s flash for
several seconds)
keypad beeps and the ARM
and READY LED’s flash for
several seconds)
PLEASE GO TO
PAGE 7 FOR
THE AGENCY
STATEMENTS
PAGE 7 FOR
THE AGENCY
STATEMENTS