Honeywell International Inc. 8DL6160RF Manuale Utente

3 

 

1. 

Enter the program mode by pressing the [1] and [3] keys simultaneously for 
a few seconds within 30 seconds after applying power or within 30 seconds 
after removing the case back.  
(Keypad Address) Enter the two digit keypad address. Press the [

✳

] key to 

continue. 

'32%((6)77

<<

01-31 

2. 

(Receiver Enable) Enter [1] to enable, or [0] to disable Receiver. Enable the 
receiver if RF transmitters or wireless keypads are programmed into the 
control. Press the [

✳

] key to continue. 

6)')-:)6

32?

3**A

 

1= ON 
0 = OFF 

3. 

If receiver is enabled, enter the two digit receiver address. 
(01-30) 
Press the [

✳

] key to continue. 

6)'%((6)77

<<

 

01-30 

4. 

(Transmitter Enable)

 

Enter [1] to enable, or [0] to disable. 

Enter [1] if bi-directional devices are being used. 

Note:   If the House ID source is the System, and more than one 6160RF is used, 

make sure only one has the Transmitter Module enabled. 

Press the [

✳

] key to continue.

 

86%271-88)6

32?

3**A

 

1= ON 
0 = OFF 

5. 

(House ID) Enter 99 (System) to use the House ID programmed into the 
control panel 
Enter 01-31 (Local) to use the House ID programmed into the 6160RF. 

Notes:  
(1) If the House ID Source is the System, RF Keypads and bi-directional units MUST 

match the House ID programmed into the panel. 

(2) If the House ID Source is Local, the RF Keypads and bi-directional units MUST 

match the House ID programmed into the 6160RF.

 

Press the [

✳

] key to continue. 

,397)-(

<<

01-31 = Local 
99 = System 

6. 

(Enable High Security mode) Enter [1] to select High Security Mode 

Note:  If this mode is enabled, the 6160RF will only recognize encrypted devices. 

Press the [

✳

] key to continue.

 

,-+,7)'96-8=

3**?

32A

1= Enable 
0 = Disable 

7. 

(Delete High Security Devices) Press the [

✳

] key to skip this prompt and 

exit Program Mode. 

Note:  If you need to delete encrypted devices refer to the Deactivating High Security 

Devices section.

 

()0)8)():-')7#

1= YES 
0 = NO 

This following procedure should be followed if using High-Security (encrypted) devices. 

1. 

Put the control panel in Go/ No Go Test mode. (See the Installation Guide for the panel being installed.) 

2. 

Follow the instruction provided with the wireless device to for installing the High-security (encrypted) device.  

3. 

The 6160RF will momentarily display the serial number of the device. 

4. 

Disable the Go/ No Go Test mode and follow the normal procedure for programming the device into the control panel 
(refer to the Installation Instructions for the device that you are programming). 

This mode gives you the ability to disable all individual wireless keys that have been directly programmed into 
the 6160RF. This is particularly useful if a user loses a wireless key. 

! 

 

1. 

Enter the keypad's local program mode within 60 seconds of power-up 
by pressing and holding down the [1] and [3] keys at the same time for 
3 seconds. The current keypad address will be displayed with the 
cursor under the "tens" digit. Press the [

✱

] key to continue. 

'32%((6)77

<<

01-31

2. 

(Delete High Security Devices) Press the [1] key to remove all high-
security (encrypted) devices. Press the [

✱

] key to continue. 

()0)8)():-')7#

23?

=)7A

 

1= YES 

0 = NO

3. 

If YES was selected in Step 2 the unit will display a confirm request to 
delete the stored high security device. Press the [1] key to accept, 
followed by the [

✳

] key to exit the programming mode. 

%6)=39796)#

23?

=)7A

 

1= YES 

0 = NO