Pioneer Corporation K071 Manuale Utente
Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the
receiving antenna; Increase the separation between the equipment and receiver;
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected; Consult the dealer or an experienced radio/TV technician for
help.
In accordance with FCC Part 15C and RSS-210, this module is listed as a Modular
Transmitter device.
1 Changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.
2 The antenna of this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitters within a host device, except in accordance
with FCC multitransmitter product procedures.
FCC Label Instructions
The outside of final products that contains this module device must display a label
referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: [AJDK071]” or “Contains FCC ID:
[AJDK071].” Any similar wording that expresses the same meaning may be used.
If the product is to be sold in Canada, then this exterior label should use wording
such as the following: “Contains Transmitter Module IC: [775E-K071]”
To satisfy FCC RF Exposure requirements for mobile and base station transmission
devices, a separation distance of 20 cm or more should be maintained between the
antenna of this device and persons during operation. To ensure compliance,
operation at closer than this distance is not recommended. The antenna(s) used for
this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the
receiving antenna; Increase the separation between the equipment and receiver;
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected; Consult the dealer or an experienced radio/TV technician for
help.
In accordance with FCC Part 15C and RSS-210, this module is listed as a Modular
Transmitter device.
1 Changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.
2 The antenna of this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitters within a host device, except in accordance
with FCC multitransmitter product procedures.
FCC Label Instructions
The outside of final products that contains this module device must display a label
referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: [AJDK071]” or “Contains FCC ID:
[AJDK071].” Any similar wording that expresses the same meaning may be used.
If the product is to be sold in Canada, then this exterior label should use wording
such as the following: “Contains Transmitter Module IC: [775E-K071]”
To satisfy FCC RF Exposure requirements for mobile and base station transmission
devices, a separation distance of 20 cm or more should be maintained between the
antenna of this device and persons during operation. To ensure compliance,
operation at closer than this distance is not recommended. The antenna(s) used for
this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.