Uniden America Corporation UT063 Manuale Utente

•  15 GMRS / 7 FRS Channels
•  121 Sub Codes
 (CTCSS Tone and DCS Code)
•  Up to 30 Mile Range*
•  Internal VOX Circuitry
•  10 Selectable Call Tone Alerts
•  Backlit LCD Display
•  2 Headset Boom mics
•  Headset Jack
•  2 Carabiner Clips

1  Antenna

2  PTT (Push-To-Talk) Button

3  Call/Lock Button

4  Menu/Power Key

5  Channel Up/Down Key

6  Weather/Monitor Key

7  Speaker

8  Headset Jack/DC 9V

9  Volume Up/Down Key

10  Microphone

11  Battery Level Meter

12  Receive Indicator

13  Call Indicator

14  Scan Indicator

15  Channel Indicator

16  Hi Power Indicator

17  Low Power Indicator

18  Transmit Indicator

19  Volume Setting Indicator

20  Keypad Lock Indicator

21  VOX Indicator

22  Weather Indicator

23  Sub Code Indicator

24  Charging Contacts

Congratulations on your purchase of the Uniden

GMR3040-2CKHS (General Mobile Radio Service)

radio. This lightweight, palm-sized radio is a state-

of-the-art device, equipped with many valuable

features. Use it at sporting events, to stay in

contact with family and friends, hiking, skiing,

outdoors, or in a neighborhood watch for vital

communication.

Your package contains two radios, two rechargeable

NiMH battery packs (#BT-805), one AC adapter (#PS-

0007), one charging cradle (#RC1285), two headset

boom mics (ZA-133), two belt clips, 2 carabiner clips

(TSTD0720002) and this reference guide. A NiMH

battery pack or 3 AAA alkaline batteries (not included)

powers each unit. To order the following optional

accessories, visit our web site at www.uniden.com or

call 1-800-554-3988 during regular business hours.

Use only Uniden accessories.
• NiMH Battery Pack - #BT-805
• Charging Cradle - #RC1285
• Headset - #ZA-133
• AC Adapter - #PS-0007
• DC Adapter - #DC-1002
• Carabiner Clip - # TSTD0720002

Each radio uses a supplied NiMH battery pack or
3 AAA alkaline batteries (not included).
To install the NiMH battery pack:
1) Make sure your radio is OFF.
2) Press the tab at the bottom of the battery

compartment door to remove the cover.

3) Install the NiMH battery pack into the battery

compartment. Be certain to follow the
instructions written on the label on the battery
pack. Installing the battery pack incorrectly will
prevent the unit from operating.

4) Replace the battery compartment door.

•  Roger Beep
•  Battery Charger
•  Battery Level Meter
•  Channel Monitor
•  Channel Scan
•  Keypad Lock
•  DC 9V Jack
•  NOAA Emergency /
 Weather Channels

This unit has a battery level meter on the display to
indicate the status of the batteries. When the
battery in the unit is low, the battery level meter
icon

flashes. Recharge the NiMH battery

pack immediately or if you are using alkaline
batteries, you must replace the alkaline batteries in
order to continue using the radio.
Warning! To avoid the risk of personal injury or

property damage from fire or electrical shock, only

use the Uniden accessories specifically designated

for this product.

If you use the rechargeable NiMH battery pack, two

radios can be charged directly or by using the

supplied charging cradle.

USING The RadIo
1) Connect the optional DC adapter (#DC-1002) to

DC 9V jack of the radio and to a cigarette lighter

port.

2) Charge the battery pack for 16 hours until the

battery indicator stops flashing.

USING The ChaRGING CRadle
1) Connect the AC adapter (#PS-0007) to DC 9V

jack and to a standard 120V AC wall outlet.

2) Set the charging cradle on the desk or tabletop,

and place the radio in the charging cradle with

the keypad facing forward.

3) Make sure that the LED illuminates. Charge the

battery pack for 16 hours and remove the radio

from the charging cradle after charging.

Note:
•  For charging batteries directly without the cradle,

In order to get the most out of your new radio, read

this reference guide completely before attempting to

operate the unit.
TURNING The RadIo oN aNd  
adjUSTING The VolUMe
1) Press and hold

MENU/   to turn the radio ON,

and increase the speaker volume by pressing

VOL ▲ . To decrease the volume, press

VOL  ▼.

2) Press and hold

MENU/   again to turn the radio

OFF.

adjUSTING The SoUNd (KeY BeepS)
Your radio emits a beep each time one of the keys

(except for the

PTT and CALL/LOCK) is pressed.

To turn this sound OFF, press and hold

LOCK while turning ON the radio. Repeat this step

to turn the sound ON.
ChooSING a ChaNNel
Your radio has 22 channels and 121 Sub codes you

can use to talk to others. In order to speak to

someone, each of you must be set to the same

channel and Sub code.
To choose a channel:
With the radio in "Normal" operating mode, press the

CH ▲ / CH  ▼ key to increase or decrease the

channel number displayed.

Note: Channels 1-7 have a typical range of up to 30

hi icon is

lo icon is displayed while scanning FRS channels.

To talk to others using the radio:
1) Press and hold the

PTT button and speak in a

clear, normal voice about 2-3 inches away from
the microphone. While you are transmitting, the

icon appears on the display. To avoid cutting

off the first part of your transmission, pause
slightly after pressing the

PTT button before you

start talking.

2) When you have finished speaking, release the

PTT button. You can now receive incoming
calls. While receiving,

displays.

MoNIToR Mode FeaTURe
Your radio allows you to listen for weak signals on

the current channel at the press of a key.
To turn ON Monitor mode:
 Press and hold

WX/MON for 2 seconds until two

beeps sound. The receiver circuit stays open,

and both noise and weak signals can be heard.

To turn OFF Monitor mode:
 Press

WX/MON to return to "Normal" mode; the

icon stops blinking and disappears.

adVaNCed FUNCTIoNS (MeNUS)
Use

MENU/   to access your radio's advanced

functions.

Normal

Normal

VOX Level

Call Tone

1-10

OFF, 1-5

Sub Code

Scan

OFF, 1-121

ON/OFF

1) Press

MENU/   to enter the menus.

2) Additional presses of

MENU/   advance you

through the menus until exiting to "Normal"

operating mode.

3) Other methods of exiting the Menu function are:
a. Press and hold

MENU/   again.

b. Press any key except

CH ▲ / CH ▼ or VOL ▲

/

VOL ▼ and wait 10 seconds until the unit

returns to “Normal” mode.

Each of the channels 1-22 may have any one of

the codes, OFF, or 1-121 selected. Code

oF (OFF)

indicates no Sub code selected and your radio can

receive a signal regardless of the code settings of

the transmitting radio.
1) Press

MENU/   to enter Menu mode. The

subcode indicator flashes.

2) Press

CH ▲ / CH ▼ key to increase or

decrease the code number displayed. You can

also select

oF (OFF) at this stage.

stay on the tone you want to select.

3) Exit Call Tone to set the selected tone.

To lock the keypad:
1) Press and hold

CALL/LOCK;   displays.

These functions are not affected by Key Lock:
•  Volume adjust
•  Call tone transmission
•  Enter monitor mode
•  PTT transmission
•  Power off
To unlock the keypad:
1) Press and hold

CALL/LOCK again;  

disappears.

aUToMaTIC poWeR SaVe
Your radio has a circuit designed to dramatically

extend the life of the batteries. If there is no

transmission or an incoming call within 3 seconds,

your radio switches to Power Save mode. The radio

is still able to receive transmissions in this mode.
lCd BaCKlIGhT
The LCD Backlight automatically turns ON when any

key (except the

PTT button) is pressed. The LCD

display illuminates for 10 seconds before turning

OFF.
RoGeR Beep
Roger Beep is a BEEP that is sent to notify the end of

transmission (both PTT and VOX transmission).

Roger Beep can be heard through the speaker when

both Roger Beep and Key Beep are set to ON. When

Roger Beep is set to ON and Key Beep is set to OFF,

Roger Beep will not be heard from the speaker but it

will be transmitted to your party. When Roger Beep is

set to OFF, Roger Beep will neither be heard nor

transmitted.
To change Roger Beep setting:
Press and hold

VOL ▲ while turning the radio on and

off. If Roger Beep is ON, it will be turned off; if it is

OFF, it will be turned on.

3) Press

MENU/   to exit Menu mode.

4) Press any key other than

CH ▲ / CH ▼ or

VOL ▲ / VOL ▼ and the radio returns to

Idle mode in 10 seconds.

Your radio has a channel scan feature that

allows you to easily scan all 22 channels.

When an active channel is detected, the radio

pauses on that channel until the channel is

clear. Then, after a 2 second delay, the radio

continues scanning. Pressing the

PTT button

while the scan is paused on a channel allows

you to transmit on that channel.
To turn ON channel scan:
1) Press

MENU/   repeatedly until the scan...

icon and

oF blink.

2.  Press

CH ▲ / CH ▼ to select Scan mode

and press

MENU/   to start it.

To turn OFF channel scan:
1) Press

MENU/   when the scan setting is

oF.

2) Press any key other than

CH ▲ / CH ▼ or

VOL ▲ / VOL ▼ to turn channel scan off in

10 seconds.

Your radio is equipped with a user selectable

Voice Operated Transmitter (VOX) that can be

used for automatic voice transmissions. The

VOX feature is designed to be used with or

without a headset with a microphone.

Transmission is initiated by speaking into the

microphone instead of pressing

PTT.

To select VOX level:
1) Press

MENU/   repeatedly until the vox

icon and the VOX sensitivity level (OFF, 1-5)

blink.

2) Press

CH ▲ / CH ▼ to change the VOX

sensitivity levels. Use level 1 for increased

sensitivity to voice in normally quiet

environments, and use a higher level to

reduce undesired activation in very noisy

environments.

Your radio is equipped with 10 selectable call

tones that are transmitted when

CALL/LOCK is

pressed.
To select a call tone:
1) Press

MENU/   repeatedly until the CALL

icon and Call Tone start to blink on the

display.

2) Press

CH ▲ / CH ▼ to move through the

available call tones. Each tone will be heard

through the speaker but will not be

transmitted. Cycle through these tones and

You can use a headset (#ZA-133) for more private

communications. To use a headset, lift the rubber

cover from over the headset jack, then plug in the

headset.
Important: Your radio is not weather resistant