UTC Fire & Security Americas Corporation Inc 764A-SMOKE Manuale Utente
Page 1
System Sensor Smoke Sensor
System Sensor Smoke
Sensor Model 2100ARFT
Sensor Model 2100ARFT
Document Number: 466-xxxx Rev. A PRELIMINARY
August 1998
August 1998
INSTALLATION
INSTRUCTIONS
INSTRUCTIONS
Product Summary
The System Sensor™ Smoke Sensor Model 2100ARFT
(smoke alarm) is a Learn Mode, wireless, photoelectric
smoke sensor with a self-contained alarm siren, a low-
battery annunciator, and a status light. The smoke
alarm is part of a security/fire alarm system and com-
municates with the system’s control panel.
(smoke alarm) is a Learn Mode, wireless, photoelectric
smoke sensor with a self-contained alarm siren, a low-
battery annunciator, and a status light. The smoke
alarm is part of a security/fire alarm system and com-
municates with the system’s control panel.
Figure 1 illustrates the smoke sensor’s parts.
Installation Guidelines
ν
Avoid installing the unit until all contsruction is
completed. The mounting ring may be pre-
installed.
completed. The mounting ring may be pre-
installed.
ν
Leave the orange dust cover on the unit until
sheet rocking and sanding are completed; other-
wise, dust can get into the unit and cause false
alarms.
sheet rocking and sanding are completed; other-
wise, dust can get into the unit and cause false
alarms.
CAUTION:
The orange dust cover must be
removed for the unit to detect
smoke.
removed for the unit to detect
smoke.
ν
Do not mix battery brands.
ν
Not compatible with CareTaker Plus or custom
versions with software versions 3.0 or earlier.
versions with software versions 3.0 or earlier.
ν
Not compatible with Commander 2000 or custom
versions with software versions 4.0 or earlier.
(The Commander 2000 announces the version
when it is powered up or reset.)
versions with software versions 4.0 or earlier.
(The Commander 2000 announces the version
when it is powered up or reset.)
Tools Needed
ν
Phillips screwdriver and pocket-sized slotted
screwdriver
screwdriver
Batteries
UL Note:
Each smoke alarm uses two 3-volt lithium
batteries. For UL installations, use one of
the following: Sanyo CR123A, Panasonic
CR123A, or Duracell DL123A. Do not mix
brands.
batteries. For UL installations, use one of
the following: Sanyo CR123A, Panasonic
CR123A, or Duracell DL123A. Do not mix
brands.
Inserting Batteries
The batteries must be correctly installed before the
panel can learn the smoke alarm ID. [Batteries are
shipped in the unit backwards.] You must remove
them and reinstall them correctly.
panel can learn the smoke alarm ID. [Batteries are
shipped in the unit backwards.] You must remove
them and reinstall them correctly.
To insert batteries into the smoke sensor:
1.
Gently twist the cover counterclockwise to sepa-
rate it from the mounting bracket.
rate it from the mounting bracket.
2.
Remove the batteries from the battery compart-
ment.
ment.
3.
Insert the batteries into the battery compartment.
Observe proper polarity.
Observe proper polarity.
4.
Leave the mounting ring off and proceed to
“Learning the Smoke Sensor.”
“Learning the Smoke Sensor.”
Low Batteries
When the batteries need to be replaced, the unit trans-
mits a signal to the panel. If the batteries are not
replaced within 7 days, the unit will chirp every 40
seconds until the batteries are exhausted.
mits a signal to the panel. If the batteries are not
replaced within 7 days, the unit will chirp every 40
seconds until the batteries are exhausted.
Note:
If you test the smoke alarm or it goes into
alarm during this 7-day period, chirp delay is
canceled and the unit begins chirping immedi-
ately.
alarm during this 7-day period, chirp delay is
canceled and the unit begins chirping immedi-
ately.
Programming
For more detailed programming information, refer to
the specific panel’s installation manual.
the specific panel’s installation manual.
60-838-95
EXHIBIT G