Shenzhen Nello Electronics Technology Co. Ltd G1 Manuale Utente

1. Camera Status LED

2. Charger Status LED

1. Connect your camera to a power source 

using the supplied Micro-USB cable.

2. The “Charger Status LED” turns green, 

when your camera is fully charged. While 

it's charging, “Charger Status LED” turns 

orange.

1. Find the microSD slot located at the 

bottom of the camera.

2. Insert a microSD card with the gold-plated 

side facing the same direction as the lens.

3. The card will make a slight clicking sound, 

when it’s securely inserted.

1. Press the “Shutter Button”.
2. The “Camera Status LED” will flash red, and your camera 

will beep.

1. Press and hold the “Shutter Button” until recording 

starts.  

2. The “Camera Status LED” will keep flashing red while 

recording. You'll also hear camera beep. 

3. Press the “Shutter Button” again to stop recording.  
4. The “Camera Status LED” will keep flashing green, and 

your camera beeps again.

1. Press and hold the “Shutter Button” until recording 

starts.

2. The “Camera Status LED” will keep flashing red while 

recording. You'll also hear camera beep twice.

3. Release the “Shutter Button” to stop recording, and 

your camera beeps again.

4. The “Camera Status LED” will keep flashing green.

1. Confirm that camera is powered on.
2. Press the “Power/Wi-Fi Button” to turn on Wi-Fi. The 

“Camera Status LED” will keep flashing blue for 3 

seconds, and camera enables Wi-Fi connection for 

120 seconds.

1. Press the Home button, and then tap Settings > Wi-Fi.
2. Be sure that Wi-Fi is on, and then select the name of 

your camera from the list. By default, the name will 

be something like “CAM…”.

3. Enter the default password 12345678, and then tap 

Join or Connect.

4.Press the Home button, and then tap the camera app 

icon NeoMe on your phone.

Dimension: 42mm x 42mm x 20mm

Weight: 25g

Video: 1080p FHD

Picture: 8M

Wireless: 802.11b/g/n

Video Streaming and Recording: 1 hour

Software Support: Android 4.2 or above, iOS 7.0 or above

Operating Temperature: 32°F to 104°F (0°C to 40°C)

Storage Temperature: -4°F to 176°F (-20°C to 80°C)

Buzzer

Charger

Status LED

Shutter Button

microSD

Slot

Micro-

USB

Port

Camera 

Status LED

Motion

Sensor

Power/

Wi-Fi

Button

Status
Power on and Standby
Taking photo
Recording video
Enabling Wi-Fi

System error 

(As: SD memory full, no SD card, etc.)

Removable USB driver mode 

(Link to PC)

LED behavior 
Flashing green
Flashes red once
Flashing red
Flashing blue for 

3 seconds
Turns yellow

Turns white

Status
Charging
Full charge
Low battery

LED behavior
Turns orange
Turns green
Flashing red

Wireless Camera

User Manual

Clip

Viscose

Sucker

Magnet

 Micro-USB 

Cable

User Manual

1. On your Phone, open the App store or Play store app.
2. Search for NeoMe app.
3. Tape Free > Install to download and install the camera 

app.

Federal Communications Commission (FCC) Statement
This device complies with Part 15 of the FCC Rules. Operation is 

subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including 

interference that may cause undesired operation of the device.
Use only the integral antenna supplied by the manufacturer 

when operating this device. Unauthorized antennas, 

modifications, or attachments could damage the TI Navigator 

access point and violate FCC regulations. Any changes or 

modifications not expressly approved by the party responsible 

for compliance could void the user's authority to operate this 

equipment.
This equipment has been tested and found to comply with the 

limits for a Class B digital device, pursuant to part 15 of the FCC 

rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate 

radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular 

installation.

CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN 
INCORRENT TYPE.
DISPOSE OF USED BATTERY ACCORDING TO THE 

INSTRUCTIONS.

 If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for 

help.
For product available in the USA/Canada market, only channel 

1~11 can be operated. Selection of other channels is not 

possible.

1.  Simply press the “Power/Wi-Fi Button” 

to power on your camera.

2.  The “Camera Status LED” will keep 

flashing green.

3.  Simply shake your camera motion 

sensor to instantly power on it, if it idles 

over 50 seconds and enters sleep mode 

automatically.

4.  Motion sensor will not power on your 

camera, if it idles over 50 seconds for 

three times without any operation.

Live Camera

Live Camera

portable exposure condition without restriction.

The device can be used in

The device has been evaluated to meet general RF exposure requirement.