Changxing Potek Electronics & Technology Co. Ltd. TX219 Manuale Utente
User manual
UP key all open, down key all close, right key make bright, left key make dark, favorite store the
suitable brightness
suitable brightness
Transmitter matching instruction: After long press the receiver ON key 5 seconds into learning
state, seven LED shining. Press ON key then press OFF key, LED Stop flash, ON/OFF function is
normal, it means learning success, otherwise quit 1 minute later
Matching clear function, when in learning state, long press ON key five seconds into clear state,
then seven LED quick blink, repress ON key clear the matching code, otherwise quit 1 minute later.
state, seven LED shining. Press ON key then press OFF key, LED Stop flash, ON/OFF function is
normal, it means learning success, otherwise quit 1 minute later
Matching clear function, when in learning state, long press ON key five seconds into clear state,
then seven LED quick blink, repress ON key clear the matching code, otherwise quit 1 minute later.
Suitable brightness store function: Adjust the brightness to the suitable state, long press Favorite
key five second, seven LED will blink one time, it means stored success, repress Favorite key, this
brightness will be invoke(Note: Suitable brightness will be 50%)
Five key transmitter’s function operation is same as above. Two key transmitter only have ON,
OFF function.
key five second, seven LED will blink one time, it means stored success, repress Favorite key, this
brightness will be invoke(Note: Suitable brightness will be 50%)
Five key transmitter’s function operation is same as above. Two key transmitter only have ON,
OFF function.
Brightness adjusting range locking function (because of matching problem it will appear bad
phenomenon such as flash, turn out in the adjusting process when on certain load light we can use
locking function.)
phenomenon such as flash, turn out in the adjusting process when on certain load light we can use
locking function.)
Press Favorite and right key at the same time, enter the maximum lock function setting, LED slow
flash, press left right key adjust to the suitable brightness, press OFF key stored, if no action with 5
seconds in the setting process, it will exit the setting state.
Press Favorite and left key at the same time, enter the minimum lock function setting, LED slow
flash, press left right key adjust to the suitable brightness, press OFF key stored, if no action with 5
seconds in the setting process, it will exit the setting state.
flash, press left right key adjust to the suitable brightness, press OFF key stored, if no action with 5
seconds in the setting process, it will exit the setting state.
Press Favorite and left key at the same time, enter the minimum lock function setting, LED slow
flash, press left right key adjust to the suitable brightness, press OFF key stored, if no action with 5
seconds in the setting process, it will exit the setting state.
Electrical parameters: DC 3V by CR2032 Battery
Frequency: 315MHz
Remote control distance: ≥80 feet
Frequency: 315MHz
Remote control distance: ≥80 feet
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a