Shenzhen Mengxiang Technology Co. Ltd C2 Manuale Utente

Manual

C2 bluetooth speaker clock

1. Put the size AA battery into the box, and set the right time.

2. Connect the DC cable with DC adaptor, and turn on the

power on-off, when hear”beep”, the clock is on.

3. Connect the clock with your phone by bluetooth. Theproducts’

bluetooth name is C2. when succeeding pairing, you should

hear”beep beep”, and the blue LED will flash.

 Front

power on-off

indicator LED

Back

Remark: pay attention to the negative and positive.

battery box

Timing knob

DC cable

◆ Size：260X260X38.9mm

◆ BT working distance：10m

◆ Product weight: 

(including the battery pack): 270g

◆  Working voltage : 3.3-5V  

◆  Power supply : DC 9V、1.5A

◆  Frequency Response : 120Hz~16KHz

◆  Bluetooth IC & version : CW6686E V4.2

◆  Output power : 7W*2 RMS(THD=10%)

Consult the after-sale service for help.

Any copy, changes or modifications of the user manual not expressly approved

unless dealer’s permission. 

◆  S/N : ≥70db

◆  Distortion : ≥<0.5%

◆  Driver Size  :  2"

1、Do not use the bluetooth speaker clock near water or humid; do not use the device

near the bathtub, water tank, swiming pool and so on.

2、Do not install the bluetooth speaker clock in the hot or cold environment. 
3、Do not expose the device in the sunshine directly.
4、Do not use the device near fire, such as, stove, candle or fireplace and so on.
5、Do not use abrasive cleaning solvents to clean the bluetooth speaker clock, 

and charge the apparatus and install the AA size battery in time to make sure the 

device work. 

1 . Do not take this apparatus apart or repait it.
2 . Do not use this apparatus near water and humid

3. Clean only with a dry cloth.

You may within 1 year from your original date of purchase return it to the authorized

service for repair.

1. Go to SETTINGS> bLUETOOTH(make sure bluetooth is

turned ON)

2. When your bluetooth enabled device finds the speaker,

select “C2” from the list of found devices. When

succeeding pairing, you will hear “beep beep”. And the

blue led light will flash slowly.

1. Go to SETTINGS> bLUETOOTH(make sure bluetooth is

turned ON)

2. When your bluetooth enabled device finds the speaker,

select “C2” from the list of found devices. When

succeeding pairing, you will hear “beep beep”. And the

blue led light will flash slowly.

This equipment has been tested and found to comply with the 

limits for a Class B digital device, pursuant to part 15 of the 

FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate 

radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference 

to radio or television reception, which can be determined by 

turning the equipment off and on, the user is encouraged to 

try to correct the interference by one or more of the following 

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Caution: Any changes or modifications to this device not 

explicitly approved by manufacturer could void your authority 

to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation 

is subject to the following two conditions: (1) This device may 

not cause harmful interference, and (2) this device must 

accept any interference received, including interference that 

may cause undesired operation.

RF Exposure Information

The device has been evaluated to meet general RF 

exposure requirement.