eMoMo Technology Co. Ltd W602 Manuale Utente
Position indicators
Adjust recliner
Adjust temperature
Turn on/off
Turn on /off massage function
Heat time indicators
Temperature indicators LOW
♦Please read the user manual carefully before using.
♦Apply to 110V-240V.
♦Please use the original switch power supply.
♦Do not use when the fabric is fold or get wrinkled.
♦Do not detach and wash the fabric.
♦Please keep away from acid and alkaline liquid.
♦Not apply to children, pregnant woman, people who suffer
from bleeding tendency and bleeding illness, tuberculosis
malignant tumor and is not sensitive to heat.
♦Please troubleshoot the problems as <Frequently asked questions>
on this manual. If the problem is not mentioned, please cal
♦Apply to 110V-240V.
♦Please use the original switch power supply.
♦Do not use when the fabric is fold or get wrinkled.
♦Do not detach and wash the fabric.
♦Please keep away from acid and alkaline liquid.
♦Not apply to children, pregnant woman, people who suffer
from bleeding tendency and bleeding illness, tuberculosis
malignant tumor and is not sensitive to heat.
♦Please troubleshoot the problems as <Frequently asked questions>
on this manual. If the problem is not mentioned, please cal
l
after-sel
service. Do not try to repair by yourself, or it may cause void warranty.
Cautions
Buttons and functions
Specification
♦Rated power:58W
♦Rated input:29V
♦Rated currenty:2A
♦Input for knob:3V
♦Remote battery:7#AAA
♦Rated input:29V
♦Rated currenty:2A
♦Input for knob:3V
♦Remote battery:7#AAA
Operation
Frequently asked quesitions
♦ Press on the rear cover of the remote and pull towards to
the remote bottom to remove the back-up cover, then install 2pcs
♦Disconnect the power supply
♦Press and hold TIME- for about 4s until the neck light flashes,
the remote bottom to remove the back-up cover, then install 2pcs
♦Disconnect the power supply
♦Press and hold TIME- for about 4s until the neck light flashes,
then connect the power in 15s. The neck light lights off, pair successfully.
♦ Press it to turn on the device and heat function. Press it again
♦M Turn on/off massage function
1st press: Turn on massage function and all vibrators work in 3 modes cyclically.
It works in each mode for 1 min then switch into the next mode automatically.
2nd press: Turn off massage function.
♦ Recline the headrest
♦ Lift the headrest.
♦ Open the chair.
♦ Close the chair.
♦ Reset the chair
♦ TIME- Press it to decrease the heat time. 15′/30′/60′available.
2nd press: Turn off massage function.
♦ Recline the headrest
♦ Lift the headrest.
♦ Open the chair.
♦ Close the chair.
♦ Reset the chair
♦ TIME- Press it to decrease the heat time. 15′/30′/60′available.
♦ TIME+ Increase heat time.15′/30′/60′available.
♦ TEMP.- Lower the heat temperature. Low/Med/High available. If it heats @low
mode, the upper-left indicator lights red. If it heats @med mode, the upper indicator lights red.
If it heats @high mode, the upper-right indicator lights red.
♦ TEMP.- Lower the heat temperature. Low/Med/High available. If it heats @low
mode, the upper-left indicator lights red. If it heats @med mode, the upper indicator lights red.
If it heats @high mode, the upper-right indicator lights red.
♦TIME- Decrease massage time.15′/30′/45′ available.
♦TIME+ ncrease massage time.
♦TIME+ ncrease massage time.
I
15′/30′/45′available.
♦INTENSITY- Decrease massage intensity. Low/Med/High available.
♦ TEMP. Upgrade the heat temperature. Low/Med/High available.
+
♦INTENSITY Upgrade massage intensity. Low/Med/High available.
Turn on/off heat function
Adjust massage
Massage time indicators
Massage intensity indicators
to turn off the device and all functions. Press and hold for 3s to turn on/off the flashlight.
If there is only 15 minutes left, press TIME- to turn off heat function.
TIME
TEMP.
TIME
INTENSITY
/MID/HIGH
7#AAA batteries
(Ensure “+” and “-”is proper)。
ISSUE
PROBABLY REASON
TROUBLE SHOOTING
♦The remote does
not work
not work
♦Without battery or
batteries are
installed incorrectly.
♦The batteries have
been ran out.
batteries are
installed incorrectly.
♦The batteries have
been ran out.
♦Install 2 pcs 7#AAA
batteries correctly.
♦Replace 2 new batteries.
batteries correctly.
♦Replace 2 new batteries.
♦The device does
not work.
not work.
♦Power supply is
disconnected or
isn't connected
properly.
♦The device hasn’t
paired successfully.
disconnected or
isn't connected
properly.
♦The device hasn’t
paired successfully.
♦Replug the power supply.
♦Re-pair signal.
♦Re-pair signal.
♦The device shut
down suddenly.
down suddenly.
♦Shut down auto-
matically as limited
time has run out.
♦ Connectors do
not connect
properly.
matically as limited
time has run out.
♦ Connectors do
not connect
properly.
♦Restar the device.
♦Check all connectors
and re-connect if it is
necessary.
♦Check all connectors
and re-connect if it is
necessary.