Texas Instruments ACS6420 Manuale Utente

 

 

 
 
 
 
 
 
 
 
 

 

 

 

11-06-21-713  09/02 

 
 

 

This package includes: 

1 

S6410 or S6420 Reader with back plate 

2 

#6 Phillips-head machine mounting screws 

2 

#6 Phillips-head self-tapping mounting screws 

1 

Phillips-head cover screw 

1 

Security-head cover screw 

1 

Installation guide (this sheet) 

 
If  any items are missing from the package, please contact the 
appropriate technical support agent:

 

USA 

1-888-937-6536 or 
1 (972)-575-4364 

Belgium (English) 

+32 (0)2 7455455 

France (English)  

+33 4 93 22 22 00 

Germany 

+49 (0)8161 80 2200 

Italy 

+39 (0)39 6568 210 

Netherlands (English) 

+31 (0)546 879 222 

Spain 

+34 902 19 73 96 

Sweden (English) 

+46 (0)8 58755527 

UK 

+44 (0)1604 88 4088 

or visit us at:  www.ti-rfid.com  

 

 

Operating Frequency 

13.56 MHz 

Supported Protocols 

ISO/IEC 15693 (Vicinity)  

Supply Voltage 

9 - 14 VDC, built-in overvoltage  

and reverse polarity protection 

Power Consumption 

90 mA Quiescent, 200 mA Read, 300 mA Max 

RS-485 Baud Rates 

9600, 19200, 38400 (Default) 

Communication 
Interface 

Wiegand 26-64 bit and RS-485 protocol 

Data Signal Integrity 

500 feet Wiegand, 4000 feet RS-485 

Data Output Format 

DES Encryption Mode (Cyper Text),  

Wiegand UID Mode, Wiegand ASCII mode 

Operating Temperature 

 -20°C to +70°C 

Storage Temperature 

 -40°C to +85°C 

Humidity 

90% RH at 70°C 

Protection Class 

IP64, Potted 

Regulatory Approvals 

FCC, R&TTE (CE), UL-94 and UL-294 (ETL) 

Overall Dimensions 

5.0” x 5.0” x 1.0” 

(12.7 x 12.7 x 2.5 cm) 

5.0” x 1.7” x 1.0” 

(12.7 x 4.3 x 2.5 cm) 

Weight 

~8.5 oz (~241 g) 

~4.8 oz (~136 g) 

 
Complete warranty information can be found on the website at: 

 

 

 

© Copyright Texas Instruments. 2002 

All rights reserved. 

 

 
Determine the installation method, which parts are needed, and 
which wires will be used.  These instructions assume that the unit 
is being installed on an unprepared flat surface.  If this unit is to be 
installed in an electrical box or door mullion opening, skip to step 
3 of the installation instructions. 

 

 
1.  Use appropriate template (from back) to mark hole locations 

for wire and screws.  A set of self-tapping screws is included, 
however the holes may be pre-drilled if desired. 

2.  Drill a 3/4” (20 mm) maximum diameter hole for wire to pass 

through.  Placement of this hole is arbitrary, but it must align 
with the opening of the back plate. 

3.  Slide wiring cable through mounting plate prior to connecting 

wires.  Be sure the flat side of the plate is toward the wall.  

4.  Connect wires per the wire guide.  Cap any unused wires to 

prevent shorting. 

5.  Screw mounting plate onto surface using the appropriate 

screws provided. 

6.  Attach the housing to the mounting plate by inserting the 

upper tab(s) of the housing into the slots in the plate. 

7. 

Secure the front housing using either the included security-
head cover screw or the Phillips-head cover screw.  

 

8. 

Test unit for proper functionality.  This can be accomplished 
by bringing a card into the read field with power applied to the 
reader.    The  LED’s  and  audio  should  function  as  desired.  
Note that this test can only be performed when the unit is in 
it’s default (Wiegand) mode as shipped.

 

* Information submitted for FCC, Industry
Canada, RTTE, CE & ETL certification:
A92ACS6410 &A92ACS6420  *