Arris VAP2500 Manuale Utente

Wireless Access Point

MOTOROLA and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC. All other product or service 

names are the property of their respective owners. ©2012 Motorola Mobility LLC. All rights reserved. 

No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, 

transformation, or adaptation) without written permission from Motorola Mobility LLC. Motorola reserves the right to revise this publication 

and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change. 

Motorola provides this guide without warranty of any kind, implied or expressed, including, but not limited to, the implied warranties of 

merchantability and fitness for a particular purpose. Motorola may make improvements or changes in the product(s) described in this manual at 

any time.

590474-001-a    07/12

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 

THE UNIT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING. DO NOT PLACE OBJECTS FILLED WITH 

LIQUIDS, SUCH AS VASES, ON THE UNIT.
CAUTION: TO ENSURE REGULATORY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE 

CABLES.
CAUTION: DO NOT OPEN THE UNIT. DO NOT PERFORM ANY SERVICING OTHER THAN THAT 

Motorola may void the user’s authority to operate the device.
Postpone Wireless Access Point installation until there is no risk of thunderstorm or lightning activity in the 

area.
Do not overload outlets or extension cords, as this can result in a risk of fire or electric shock. Overloaded 

AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs are 

dangerous. They may result in a shock or fire hazard.
Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against 

them. Pay particular attention to cords where they are attached to plugs and convenience receptacles, and 

examine the point where they exit from the product.
Place this equipment in a location that is close enough to an electrical outlet to accommodate the length of the 

power cord.
Place this equipment on a stable surface.
When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric 

shock and injury to persons, including the following:
•  Read all of the instructions before you operate this equipment. Give particular attention to all safety 

precautions. Retain the instructions for future reference.

•  Comply with all warning and caution statements in the instructions. Observe all warning and caution 

symbols that are affixed to this equipment.

•  Comply with all instructions that accompany this equipment.
•  Avoid using this product during an electrical storm. There may be a risk of electric shock from lightning. For 

added protection for this product during a lightning storm, or when it is left unattended and unused for long 

periods of time, unplug it from the wall outlet, and disconnect the cable system. This will prevent damage to 

the product due to lightning and power surges.

•  Operate this product only from the type of power source indicated on the product’s marking label. If you are 

not sure of the type of power supplied to your home, consult your dealer or local power company.

•  Upon completion of any service or repairs to this product, ask the service technician to perform safety 

checks to determine that the product is in safe operating condition.

It is recommended that the customer install an AC surge protector in the AC outlet to which this device is 

connected. This is to avoid damaging the equipment by local lightning strikes and other electrical surges.
Different types of cord sets may be used for connections to the main supply circuit. Use only a main line cord 

that complies with all applicable product safety requirements of the country of use.
Installation of this product must be in accordance with national wiring codes.
Place unit to allow for easy access when disconnecting the power cord/adapter of the device from the AC wall 

outlet.
Wipe the unit with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners 

directly on the unit or use forced air to remove dust.
This product was qualified under test conditions that included the use of the supplied cables between system 

components. To be in compliance with regulations, the user must use these cables and install them properly. 

Connect the unit to a grounding type AC wall outlet using the power adapter supplied with the unit.
Do not cover the device, or block the airflow to the device with any other objects. Keep the device away from 

excessive heat and humidity and keep the device free from vibration and dust.
Installation must at all times conform to local regulations.
FCC ComplianCe Class B Digital DeviCe 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not occur in a particular 

installation.  If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one 

of the following measures:
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by Motorola for compliance could void the user’s 

authority to operate the equipment.
For operation within 5.15 ~5.25GHz /5.25 ~5.35GHz/5.47 ~5.725GHz frequency range, it is restricted to indoor 

environment. The band from 5600-5650MHz will be disabled by the software during the manufacturing and 

cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 

15.407 of the FCC Rules.
impoRtant note: 

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This 

equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Firmware setting is not accessible by the end user.
FCC DeClaRation oF ConFoRmity 

Motorola, Inc., Broadband Communications Sector, 101 Tournament Drive, Horsham, PA 19044, 1-215-323-1000, 

declares under sole responsibility that the VAP2500 complies with 47 CFR Parts 2 and 15 of the FCC Rules as 

Class B digital devices. These devices comply with Part 15 of FCC Rules. Operation of these devices is subject 

to the following two conditions: (1) These devices may not cause harmful interference, and (2) these devices 

must accept any interference that may cause undesired operation.

WiReless lan inFoRmation 

The VAP2500 products are wireless network products that use Orthogonal freguency-division multiplexing (OFDM) 

radio technology. These products are designed to be inter-operable with any other wireless OFDM type product that 

complies with:
•  The IEEE 802.11 Standard on Wireless LANs (Revision A and Revision N), as defined and approved by the 

Institute of Electrical Electronics Engineers.

•  The Wireless Fidelity (WiFi) certification as defined by the Wi-Fi Alliance.
WiReless lan anD youR HealtH 

The VAP2500, like other radio devices, emit radio frequency electromagnetic energy, but operate within the 

guidelines found in radio frequency safety standards and recommendations. 

RestRiCtions on use oF WiReless DeviCes 

In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or 

responsible representatives of the organization. For example, using wireless equipment in any environment where 

the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the applicable policy for the use of wireless equipment in a specific organization or 

environment, you are encouraged to ask for authorization to use the device prior to turning on the equipment. 
The manufacturer is not responsible for any radio or television interference caused by unauthorized modification 

of the devices included with this product, or the substitution or attachment of connecting cables and equipment 

other than specified by the manufacturer. Correction of interference caused by such unauthorized modification, 

substitution, or attachment is the responsibility of the user.
The manufacturer and its authorized resellers or distributors are not liable for any damage or violation of government 

regulations that may arise from failing to comply with these guidelines.
FCC CeRtiFiCation 

The VAP2500 contains a radio transmitter and accordingly have been certified as compliant with 47 CFR Part 15 of 

the FCC Rules for intentional radiators. Products that contain a radio transmitter are labeled with FCC ID and the FCC 

logo.
Industry Canada statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following 

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including 

interference that may cause undesired operation of the device.
Cet appareil est conforme la norme d’Industrie Canada exempts de licence RSS (s). Son fonctionnement est soumis 

aux deux conditions suivantes: (1) cet appareil ne peut pas causer d’interférences, et (2) cet appareil doit accepter 

toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l’appareil.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful 

interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply 

with the e.i.r.p. limit; and
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits 

specified for point-to-point and non point-to-point operation as appropriate.
(iv) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 

MHz and that these radars could cause interference and/or damage to LE-LAN devices
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 

5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN 

devices.
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions 

susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à 

l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les 

mêmes canaux;
(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz 

doit se conformer à la limite de p.i.r.e.;
(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la 

limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.
(iv) de forte puissance radars sont désignés comme utilisateurs principaux (c.-à-utilisateurs prioritaires) des bandes 

5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer des interférences et / ou des dommages à 

dispositifs LAN-EL
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés 

utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces 

radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
IMPORTANT NOTE:
Canada Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This 

equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum 

(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other 

users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is 

not more than that necessary for successful communication.
NOTE IMPORTANTE: (Pour l’utilisation de dispositifs mobiles)
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non 

contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de 

rayonnement et votre corps.
En vertu de la réglementation de l’industrie au Canada, cet émetteur radio peut fonctionner uniquement à l’aide 

d’une antenne d’un type et un maximum (ou moins) de gain approuvé pour l’émetteur par Industrie Canada. Pour 

réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisis afin que 

la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication 

réussie.