ICOM 217800 Manuale Utente
7
1
PANEL DESCRIPTION
■
Front panel
(continued)
#7
TRANSMIT INDICATOR [TX]
Lights red while transmitting.
#8
RECEIVE INDICATOR [RX]
Lights green while receiving a signal and when the
squelch is open.
squelch is open.
#9
LOCK INDICATOR [LOCK]
(p. 64)
Lights red when the dial lock function is activated.
$0
TRANSMIT FREQUENCY CHECK SWITCH
[XFC]
[XFC]
Monitors the transmit frequency when pushed and
held during the split frequency operation.
held during the split frequency operation.
• While pushing this switch, the transmit frequency can be
changed with the tuning dial, keypad, memo pad or the
[Y]/[Z] switches.
[Y]/[Z] switches.
• When the split lock function is turned ON, pushing [XFC]
cancels the dial lock function. (p. 99)
$1
QUICK TUNING SWITCH [TS]
(p. 26)
➥Turns the quick tuning step ON and OFF.
• While the quick tuning indicator, “Z,” is displayed
above the frequency indication, the frequency can be
changed in programmed kHz steps.
changed in programmed kHz steps.
• 0.1, 1, 5, 9, 10, 12.5, 20 and 25 kHz quick tuning
steps are available for each operating mode indepen-
dently.
dently.
➥When the quick tuning step is OFF, push for 1
sec. to turn the 1 Hz tuning step ON and OFF.
• 1 Hz indications appear in both readouts and the fre-
quency can be changed in 1 Hz steps.
➥When the quick tuning step is ON, push for 1 sec.
to enter the quick tuning step set mode.
$2
MEMORY CLEAR SWITCH [M-CL]
(p. 80)
Clears the selected readout memory channel con-
tents when pushed for 1 sec. in memory mode.
tents when pushed for 1 sec. in memory mode.
• The channel becomes a blank channel.
• This switch does not function in VFO mode.
• This switch does not function in VFO mode.
$3
MEMORY WRITE SWITCH [MW]
(p. 72)
Stores the selected readout frequency and operat-
ing mode into the displayed memory channel when
pushed for 1 sec.
ing mode into the displayed memory channel when
pushed for 1 sec.
• This function is available both in VFO and memory
modes.
$4
MEMORY UP/DOWN SWITCHES [
Y
Y
]/[
Z
Z
]
(p. 76)
➥Push to select the memory channel number for
the selected readout.
• Memory channels can be selected both in VFO and
memory modes.
➥Select the desired memory channel directly after
pushing [F-INP] and a memory channel number.
$5
MEMO PAD-READ SWITCH [MP-R]
(p. 81)
Each pushing calls up a frequency and operating
mode in a memo pad. The 5 (or 10) most recently
programmed frequencies and operating modes can
be recalled, starting from the most recent.
mode in a memo pad. The 5 (or 10) most recently
programmed frequencies and operating modes can
be recalled, starting from the most recent.
• The memo pad capacity can be expanded from 5 to 10
in set mode for your convenience. (p. 101)
BW
BW
2.4k
2.4k
SFT
SFT
0
FIL2
FIL2
qw:pp
TX
TX
CW
CW
qr.qpp.pp
21.076.50
21.076.50
VFO
VFO
U S B
U S B
1
METER
Po
ANT
1
Quick tuning indicator
NB
NR
BAL
NR
COMP BK-IN DELAY KEY SPEED
LOCK
TX
RX
TWIN PBT
CW PITCH
F-1
F-2
F-3
F-4
F-5
REC/PLAY
LOCK/SPEECH
RIT/
TX
TX
RIT
CLEAR
SPLIT
MP-W
MP-R
DUAL
WATCH
VFO/
MEMO
MAIN/
SUB
M.SCOPE
CHANGE
1.8
1
3.5
2
7
3
10
4
14
5
18
6
21
7
24
8
28
9
GENE
50
0
F-INP
ENT
Y
Z
MW
M-CL
TS
XFC
CEIVER
PBT CLR
NOTCH
NOTCH
SSB
CW/RTTY
AM/FM
FILTER
EXIT/SET
%2 %1
$7
$5
$6
$9
%0
$8
#7
#8
#9
$4
%3
$3
$2
$1
$0
$2
$1
$0