ICOM 268100 Manuale Utente
16
3
CONVENTIONAL OPERATION
3
15
3
CONVENTIONAL OPERATION
D Transmitting notes
• Transmit inhibit function
The transceiver has several inhibit functions which restrict trans-
mission under the following conditions:
The transceiver has several inhibit functions which restrict trans-
mission under the following conditions:
- The channel is in mute condition (‘Inaudible’ condition; “
”
does not appear).
- Channel is busy.
- Un-matched (or matched) CTCSS is received.
- The selected channel is a ‘receive only’ channel.
- Un-matched (or matched) CTCSS is received.
- The selected channel is a ‘receive only’ channel.
• Time-out timer
After continuous transmission for the pre-programmed time period,
the time-out timer is activated, causing the transceiver to stop trans-
mitting.
After continuous transmission for the pre-programmed time period,
the time-out timer is activated, causing the transceiver to stop trans-
mitting.
• Penalty timer
Once the time-out timer is activated, transmission is further inhibited
for a period determined by the penalty timer.
Once the time-out timer is activated, transmission is further inhibited
for a period determined by the penalty timer.
D TX code channel selection
If the transceiver has [TX Code CH Select], indication can be tog-
gled between the operating channel number (or name) and TX
code channel number (or name). When the TX code channel num-
ber (or name) is displayed, the [
gled between the operating channel number (or name) and TX
code channel number (or name). When the TX code channel num-
ber (or name) is displayed, the [
]/[
] key selects the TX code
channel.
TO SELECT A TX CHANNEL:
q Push [TX Code CH Select]— a TX code channel appears.
w Push [
q Push [TX Code CH Select]— a TX code channel appears.
w Push [
]/[
] to select the desired TX code channel.
e Push [Call] (or [PTT] during MSK operation) to transmit the se-
lected TX code.
r Push [TX Code CH Select] again to return to the operating chan-
nel number indication.
FOR TX CODE CHANNEL TYPE:
If the transceiver has a [TX Code CH Up] or [TX Code CH Down]
key, the programmed TX code channel can be selected directly.
If the transceiver has a [TX Code CH Up] or [TX Code CH Down]
key, the programmed TX code channel can be selected directly.
D TX code number edit
(PMR or BIIS PMR operation only)
If the transceiver has [TX Code CH Select] or [TX Code Enter], TX
code contents can be edited within the allowable digits.
code contents can be edited within the allowable digits.
TO EDIT A TX CODE VIA [TX CODE CH SELECT] KEY:
q Push [TX Code CH Select] to enter the TX code channel selec-
q Push [TX Code CH Select] to enter the TX code channel selec-
tion mode.
• Select the desired channel using [
]/[
] if desired.
w Push [TX Code CH Select] for 1 sec. to enter the TX code edit
mode.
e Push [TX Code CH Select] to select the desired digit to be
edited.
r Set the desired digit using [
]/[
]/[TX Code CH Up]/[TX
Code CH Down].
t Push [TX Code CH Select] to set the digit and the editable digit
move to right automatically.
y Repeat r and t to input all allowed digits.
u Push [Call] or [PTT] to transmit the selected TX code.
u Push [Call] or [PTT] to transmit the selected TX code.
TO EDIT A TX CODE VIA [TX CODE ENTER] KEY:
q Select the desired TX code channel via [TX Code CH Up]/[TX
q Select the desired TX code channel via [TX Code CH Up]/[TX
Code CH Down], if desired.
w Push [TX Code Enter] to enter the TX code edit mode.
e Push [TX Code Enter] to select the desired digit to be edited.
r Set the desired digit using [
e Push [TX Code Enter] to select the desired digit to be edited.
r Set the desired digit using [
]/[
]/[TX Code CH Up]/[TX
Code CH Down].
t Push [TX Code Enter] to set the digit and the editable digit move
to right automatically.
y Repeat r and t to input all allowed digits.
u Push [Call] or [PTT] to transmit the selected TX code.
u Push [Call] or [PTT] to transmit the selected TX code.
!IC-F50_F60 BIIS.qxd 03.9.3 1:38 PM Page 15 (1,1)