ICOM 387700 Manuale Utente

- 2 -

- 3 -

D

Indicators
q

 

Displays the relative receive signal strength level.

w 

    Displayed or blinks to indicate the battery status.

Indication

Battery 

status

Full

Mid

Charging

required

Battery

exhausted

 

 blinks when the battery is exhausted.

Icons
The following icons are displayed in the Icon Area.
SHIFT ICON 

Displayed when the Shift function is ON.

L

  A user can use a Software key’s secondary function in the Shift 

mode. Ask your dealer for details.

Displays the output power level.

 •“L1” is displayed when the output power is set to Low.

 •“L2” is displayed when the output power is set to Mid.

 •“H” is displayed when the output power is set to High.

Displayed when the channel is in the ‘audible’ (unmute) 

mode.
MESSAGE ICON  

 • Blinks after messages (Message or Status Message) have 

been received.

 • Stops blinking when the screen is changed, or any key is 

pushed, but is displayed if unread messages are still in the 

Message memory.

 • Disappears when all messages in the Message memory 

have been read.

 Displayed when a matching signal is received, depending 

on the presetting.
SCAN ICON  

 • Displayed when a scan is paused.

 •Blinks while scanning.

 Displayed when the channel is selected as a scan target channel.

NOTE: The screen is an example.

The displayed position of each icon may differ, depending 

on the function being used.

Icon Area

Text Area
Key Display

Area

 • Displayed when the Voice Scrambler function is ON.

 •Displayed when the Encryption function is ON.

 •Blinks when decoding an encrypted signal.

 •Displayed when valid position data is received.

 • Blinks when searching for satellites or calculating position 

data.

*HM-233GP is required to use the GPS function.

 •Displayed when the Record function is ON.

 •Blinks while recording audio.

TALK AROUND ICON  
Displayed when the Talk Around function is ON.
PHONE ICON  

 • Displayed when the transceiver is connected to a 

telephone network on the selected channel.

 •Blinks while receiving a phone call.

BROADCAST CALL ICON   *
Displayed when the Broadcast call is received.

* For only the dPMR version.

SITE LOCK ICON  
Displayed when the Site Lock function is ON.
LONE WORKER ICON  

Displayed when the Lone Worker function is ON.
MOTION SENSOR ICON  

Displayed when the Motion Sensor function is ON.
NOISE CANCEL ICON  

Displayed when the Noise Cancel function is ON. 
SURVEILLANCE ICON  

Displayed when the Surveillance function is ON.
VIBRATION ICON  

Displayed when the Vibration function is ON.
VOX ICON   *

Displayed when the VOX function is ON.

* VS-5MC, VS-3, or other Bluetooth headset is required to use the 

VOX function.

 •“ ” is displayed when Bluetooth

 

is activated.

 •“ ” is displayed when a Bluetooth device is connected.

D

Displays the selected Zone number, Channel number, and 

Channel name, if set.

D

Displays the names of the function assigned to [P1] and [P2].

L

  Ask your dealer about the assigned Software key functions.

D

NOTE:Beforeusingthetransceiverforthefirsttime,the

battery pack must be fully charged for optimum life and 

operation. See the BATTERY CHARGING section of this 

sheet.

Rotate [VOL] to turn ON the transceiver.

D

1.   Select a channel.

L

 Rotate [Selector] or push [Up] or [Down], depending on the 

presetting.

2.   When receiving a call, rotate [VOL] to adjust the audio 

output level to a comfortable listening level.

CAUTION: Attach an antenna before transmitting. 

Transmitting without an antenna may damage the 

transceiver.

1.  Wait until the channel is clear to avoid interference.

2.   While holding down [PTT], speak at your normal voice 

level. 

3.  Release [PTT] to receive.

To maximize the readability of your signal:

1.Afterpushing[PTT],pausebrieflybeforeyoustart

speaking.

2.  Hold the microphone 5 to 10 cm (2 to 4 inches) from 

your mouth, then speak at your normal voice level.

D

D

You can rapidly charge up to 6 battery packs with the 

optional BC-214.

Approximately 2.8 hours

 • The  BC-157S 

ac

 

adapter

 or the OPC-656 

dc

 

power

 

cable

 • The  AD-132N 

charger

 

adapter

 (may be supplied with the 

charger, depending on the charger version)

CAUTION: NEVER reverse the polarity when connecting 

the OPC-656 to a power source. This will ruin the battery 

charger.

Red line: +, Black line: _

OPC-656
Connect to a 

DC power supply: 

12 to 16 V, at least 7 A

Red line:   +  

Black line: _

Turn 

To an AC outlet

You can rapidly charge the Li-ion battery pack with the 

BC-219N.

Approximately 2.5 hours

 • A power adapter (may be supplied with the charger, 

depending on the charger version) or the OPC-515L/CP-23L 

dc

 

power

 

cables

.

CAUTION: NEVER reverse the polarity when connecting 

the OPC-515L to a power source. This will ruin the battery 

charger.
White line: +, Black line: _

 • Before detaching or attaching a battery pack, 

BE SURE to turn OFF the transceiver by rotating [VOL] fully counter clockwise, until it makes a 

“click” sound. Otherwise, a transceiver malfunction could occur.

   

 

 The 

 (For a 13.8 V DC 

power source) or the 

CP-23L (for a 12 V 

cigarette lighter 

socket) can be used 

instead of the power 

adapter.

Adapter*

*

  

A different type, or no power adapter is 

supplied, depending on the charger version.

Turn 

To an AC outlet

q

w