Sanjet Technology Corp. CR58 Manuale Utente

EN-1

EN-3

EN-4

EN-5

EN-6

EN-7

EN-8

• Do not drop, puncture or disassemble the device; otherwise 

the warranty will be voided.

• Avoid all contact with water. Dry your hands before using the 

device.

• Use the device with care. Avoid pressing hard on the device 

body.

• For your own safety, avoid using the device when there is a 

storm or lightning.

• Use only the accessories supplied by the manufacturer.
• Keep the device out of the reach of infants.
• When you get off the car, do not leave the device on the 

dashboard where it is subject to direct sunlight.

• The battery is integrated with the device. Do not dissemble and 

modify. The battery should be replaced by an authorized 

service center only.

This device complies with Part 15 of the FCC Rules. Operation is 

subjected to the following two conditions: (1) this device may 

not cause harmful interference, and (2) this device must accept 

any interference received, including interference that may cause 

undesired operation.

This equipment has been tested and found to comply with limits 

for a Class B digital device, pursuant to Part 15 of the FCC rules. 

These limits are designed to provide reasonable protection against 

harmful interference in residential installations. This equipment 

generates, uses, and can radiate radio frequency energy, and if not 

installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is 

no guarantee that interference will not occur in a particular 

installation. If this equipment does cause interference to radio or 

television equipment reception, which can be determined by 

turning the equipment off and on, the user is encouraged to try to 

correct the interference by one or more of the following 

measures:

- Reorient or relocate the receiving antenna.
- Move the equipment away from the receiver.
- Plug the equipment into an outlet on a circuit different from that 

to which the receiver is connected.

- Consult the dealer or an experienced radio/television technician 

for additional suggestions.

You are cautioned that any change or modifications to the 

equipment not expressly approved by the party responsible for 

compliance could void your authority to operate such equipment.

Insert the memory card with the gold contacts 

facing to the front of the device. 

Push the memory card until it clicks into place.
About SD Card

• Please use SD card with the size/memory 

at least 4GB, Class 6 (up to 32GB).

• Be sure to format SD card using the device 

before the initial usage.

• Do not remove the memory card while recording. This may 

damage the memory card.

1. Connect one end of the USB cable to the 

micro USB port of the device.

2. Connect the other end of the USB cable to 

the computer.

NOTE
• If you using the device as a car recorder, use 

the car adapter to charge the battery. 

• Turn on the power, press the POWER button.
• Turn off the power, press and hold the POWER button for at 

least 5 seconds.

1. Make sure your smartphone is connected to the Internet.
2. Launch Play Store (Android) or App Store (iOS) application.
3. On the search bar, enter the keyword “wirecorder” to search for 

APP.

4. Download and install Wirecorder. 

After the installation is complete, 

the Wirecorder icon (       ) is 

displayed on the application screen.

NOTE
• The application UI varies depending 

on the device operating system 

and design.

To use the neck strap, do the following:
1. Press the quick release buckle to 

detach the small piece of neck straps 

that consists of a small lanyard.

2. Insert the lanyard through the strap eyelet 

on the bracket. Make a loop to secure it.

3. Install the camera into the bracket.
4. Attach the quick release buckle onto 

its slot (see Step 1 illustration).  

Press the buckle firmly until it snaps 

into place.

5. Wear the neck strap.

To wear the device on your cloth using the clothespin bracket, do 

the following:
1. Install the camera into the bracket.
2. Pinch the prongs to open the clipper and wear it on your cloth.

To wear the device on your cloth using the safety pin bracket, do 

the following:
1. Install the camera into the bracket.

2. Open the safety pin by pressing on the bar. 

Be careful with the sharp point.

3. Slide the open pin through the cloth. Then 

squeeze the pin and slide the bar back into 

position.

The device can also be used as a surveillance camera to monitor 

your home or office. To attach the stand, do the following:
1. Install the camera into the bracket. 

Then install the stand to the slot on the 

bracket.

2. Place the stand on a stable surface.

1. On your smartphone, launch Settings application.
2. In WIRELESS & NETWORKS, tap Wi-Fi and set it to ON.

The available networks are listed.

3. Tap TESTAP to connect to the 

camera. 

4. Enter the password and tap Connect. 

NOTE
• The default password is “1111111111”.
• You can change the SSID and password in Setup mode.

Camera

Clothespin Bracket

Neck Strap

USB Cable

Car Adapter

Car Bracket

Safety Pin Bracket

The following items come with your package.

EN-2

Camera Stand

The device can be used as a car recorder. To mount the device in 

your car, do the following:
1. Install the camera into the 

bracket.

2. With the suction-cup laying flat, position 

the suction cup on the windshield.

3. Hold the base firmly on the windshield 

and press down the clamp to mount 

the car bracket to the windshield. 

4. Adjust the device position.

Loose the knob to swivel the device 

vertically or horizontally (up to 360°). 

Then tighten the knob to make sure 

the device is securely locked in place.

POWER button

HDMI port

SHUTTER button

Microphone

Microphone

Micro SD card slot

LED indicators

Micro USB port

SAR test distance is 5 mm.