G-Light Technology Co. Ltd. RLTXA06 Manuale Utente
fig.7-1
fig.7-2
Programming
Programming Instruction
Suitable for first installion or big changes for whole system.
Press the programming button on the receiver module for 5 seconds
(see Fig.7-1), until the LED on receiver module flashes Green, release
the programming button, the receiver is now in learning mode.
a). If the LED on the receiver module flashes green, there is still
suffiient memory to program extra wall switches, if the LED
flashes red, then the memory is full, the receiver will accept up
to 20 codes.
b). Press the remote switch button(Fig.7-2) that you wish to program
to the reciever.
c). When receiver module received the remote switch signal, LED on
receiver module will flash orange. The switch is now programmed
to the receiver. If more than one switch needs to be programmed
to the receiver (Maximum 20) repeat steps.
When the second switch is pressed the orange LED with flash twice,
if a third switch is pressed the orange LED will flash three times, etc.
Remote switch is through the programming way to coupling with receiver
module. Each remote switch is programmable with single or multiple
receiver module. Or, each receiver module is programmable with single
or multiple remote switches.
A. Using programming button on the receiver module
Please take the receiver module and installed it as per wiring diagram
instruction manual. Preparing the remote switch that ready for
programming. Press the remote switch button to make sure the remote
switch battery is powered and working fine. LED on remote switch will
flash orange. Considering different situation and future increase or changes,
there are ways to enter programming mode as below.
-2-
●
Each receiver module can accept up to 20 codes.
●
Anytime want to leave programming mode, just press the button on receiver module.
●
When you have entered programming mode, if you do not press any button
within 15 seconds, the sytem will leave programming mode automatically.
**Note:
If original programmed wireless remote switch still operated.
1).
Press and hold the button on the existing remote switch for 10 seconds until LED on switch
starts to flash.
2). Press the button on the existing remote switch once again within 3 seconds and the LED on
receiver module will start to flash green, the receiver is now in programming mode.
When receiver module received the remote switch signal, LED on receiver modue
will flash orange. The switch is now programmed to the receiver. If more than one
switch needs to be programmed to the receiver (Maximum 20) repeat steps.
When the second switch is pressed the orange LED with flash twice, if a third switch
is pressed the orange LED will flash three times, etc.
B. Use the existing remote switch to program extra remote switches
●
Each receiver module can accept up to 20 codes.
●
Anytime want to leave programming mode, just press the button on receiver module.
●
When you have entered programming mode, if you do not press any button
within 15 seconds, the sytem will leave programming mode automatically.
**Note:
Delete Memory
●
To cancel / delete original all memory from the receiver. Press and hold the programming
button on receiver module (fig.7-1) for 20 seconds until LED turns Red. When
LED turns RED the memory in the receiver is cleared.
**Note: When you press and hold the programming, the LED will flash green after
5 seconds, continue to hold the programming button for the 20 seconds until it turns
RED.
●
To cancel / delete single memory from the receiver.
Please make sure the remote switch that has been programmed into the receiver that
you wish to delete.
Press the programming button on the receiver module for 5 seconds (see Fig.7-1), until the
LED on receiver module flashes Green, release the programming button, the receiver is now
in progrmming mode.
a). If the LED on the receiver module flashes green, there is still suffiient memory to program
extra wall switches, if the LED flashes red, then the memory is full, the receiver will accept
up to 20 codes.
b). Press the remote switch button that you wish to DELETE to the reciever。
c). When receiver module received the remote switch signal, LED on receiver module will flash
RED. The switch is now DELETED from the receiver. If more than one switch needs to be
deleted to the receiver, repeat steps.
When the switch is pressed the RED LED with flash twice that was the original memorized
sequence in receiver, if a third switch is pressed the RED LED will flash three times, etc.
Trouble Shooting
When you find the remote light switch is not working, please check following:
1) Press the remote light switch:
If LED do not flash. Please insert new battery.
If LED flashes quickly, please insert new battery.
If LED flashes once, that means the remote switch is working properly.
2) Press the remote light switch, it will send the signal to the compatible receiver module.
If receiver receives the signal, the LED on receiver will flash 0.5 seconds to confirm
receiving OK. If LED on receiver do not flash, that means the programming incorrectly,
please re-program.
3) Press the receiver module button 2 times, if the connected light fixture is responsed, that
means the wire connection is correct. If any light fixture is not reponsed, please check
the light if faulty.
FCC Part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause hamful interference and
(2) this device must accept any interference received including interference that may cause
undesired operation.
FCC Part 15.21 information for user
You are cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
FCC Section 15.105 Information to the user.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in the particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on the circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.