ELAD srl FDM-S2 Manuale Utente

Pagina di 32
ELAD FDM-S2 
 
User Manual Rev 1.03   05/2014 
 
© 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or 
by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
 
 
30 
FDM-S2 Technical Specifications 
 
 
ELAD FDM-S2 
TECHNICAL SPECIFICATIONS 
GENERAL 
Frequency Coverage 
HF+50MHz Band (10 kHz ÷ 54 MHz): Direct Sampling Mode 
VHF1 Band (74-108MHz): Undersampling Mode 
VHF2 Band (135-148MHz): Undersampling Mode 
Bypass for experimenting use 
Antenna Connectors 
HF+50MHz Band input: SMA (50 Ω) SMA/BNC adapter included 
VHF1 & VHF1 Bands input: SMA (50 Ω) SMA/BNC adapter included 
Temperature Range 
0 ÷ 40 °C 
PC Interface 
High-Speed USB 2.0 (480 Mbit/s) 
Power Supply 
USB powered with double USB cable (included) 
Power Consumption 
Less than 4 W (5 V-750 mA) from USB (double USB cable required) 
With slow Sample Rate Dlls (for example  192kSamp/sec) typical 2.6 W  
External I/O Connector 
Female DB9 (mute control, I
2
C and SPI interface) 
Absolute Maximum 
RF Input Level 
+20 dBm 
Dimensions 
110 (W) x 40 (H) x 90 (D) mm 
Weight 
360 g 
 
HF+50MHz 
Band 
RECEIVER 
Configuration 
Direct sampling – ADC DDC with FPGA Xilinx Spartan6 XC6LXC25 
A/D Conversion 
122.88 MSPS @ 16 bit/sample 
Sensitivity 
HS
(1)
 Typical: 
-122 dBm (CW, BW 500 Hz, 10 dB (S+N)/N) 
LS
(2)
 Typical: 
-110 dBm (CW, BW 500 Hz, 10 dB (S+N)/N) 
3
rd
 Oder Intercept Point 
HS
(1)
 Typical: 
+23 dBm @ 14 MHz, Spacing 2 kHz 
+16 dBm @ 50 MHz, Spacing 2 kHz 
LS
(2)
 Typical: 
+31 dBm @ 14 MHz, Spacing 2 kHz 
+25 dBm @ 50 MHz, Spacing 2 kHz 
Blocking Gain 
Compression 
Typical: > 115 dB @ 10 MHz, Spacing 2 kHz, CW, BW 500 Hz 
Noise Floor (MDS) 
HS
(1)
 Typical: 
-132 dBm @ 14 MHz, CW, BW 500 Hz, NR
(3)
 Off 
-138 dBm @ 14 MHz, CW, BW 500 Hz, NR
(3)
 On 
-130 dBm @ 50 MHz, CW, BW 500 Hz, NR
(3)
 Off 
-136 dBm @ 50 MHz, CW, BW 500 Hz, NR
(3)
 On 
LS
(2)
 Typical: 
-120 dBm @ 14 MHz, CW, BW 500 Hz, NR
(3)
 Off 
-126 dBm @ 14 MHz, CW, BW 500 Hz, NR
(3)
 On 
-118 dBm @ 50 MHz, CW, BW 500 Hz, NR
(3)
 Off 
-124 dBm @ 50 MHz, CW, BW 500 Hz, NR
(3)
 On 
Clipping Level 
HS
(1)
: -8 dBm @ 14 MHz, -12 dBm @ 50 MHz 
LS
(2)
: +4 dBm @ 14 MHz, 0 dBm @ 50 MHz 
Internal Spurious Carriers  Typical: < -115 dBm @ 384 kSamp/sec, HS
(1)
 
 
VHF1 
Band 
RECEIVER
 
Configuration 
Undersampling – ADC DDC with FPGA Xilinx Spartan6 XC6LXC25 
A/D Conversion 
122.88 MSPS @ 16 bit/sample 
Sensitivity 
(WBFM @ 12 dB SINAD) 
HS
(1)
 Typical: 2.5 µV @ 98 MHz 
LS
(2)
 Typical: 10 µV @ 98 MHz 
3
rd
 Oder Intercept Point 
HS
(1)
 Typical: +21 dBm @ 98 MHz, Spacing 2 kHz  LS
(2)
 Typical: +29 dBm @ 98 MHz, Spacing 2 kHz 
Noise Floor (MDS) 
HS
(1)
 Typical: 
-126 dBm @ 98 MHz, CW, BW 500 Hz, NR
(3)
 Off 
-132 dBm @ 98 MHz, CW, BW 500 Hz, NR
(3)
 On 
LS
(2)
 Typical: 
-114 dBm @ 98 MHz, CW, BW 500 Hz, NR
(3)
 Off 
-120 dBm @ 98 MHz, CW, BW 500 Hz, NR
(3)
 On 
Clipping Level 
HS
(1)
: -3 dBm @ 98 MHz 
LS
(2)
: +9 dBm @ 98 MHz 
Internal Spurious Carriers  Typical: < -110 dBm @ 384 kSamp/sec, HS
(1)
 
 
VHF2 
Band 
RECEIVER
 
Configuration 
Undersampling – ADC DDC with FPGA Xilinx Spartan6 XC6LXC25 
A/D Conversion 
122.88 MSPS @ 16 bit/sample 
Sensitivity 
(FM @ 12 dB SINAD) 
Typical: 
0.4 µV @ 145 MHz, NR
(3)
 Off 
0.2 µV @ 145 MHz, NR
(3)
 On 
3
rd
 Oder Intercept Point 
Typical: +5 dBm @ 145 MHz, Spacing 2 kHz 
Noise Floor (MDS) 
Typical: 
-137 dBm @ 145 MHz, CW, BW 500 Hz, NR
(3)
 Off 
-143 dBm @ 145 MHz, CW, BW 500 Hz, NR
(3)
 On 
Clipping Level 
Typical: -19 dBm @ 145 MHz 
Internal Spurious Carriers  Typical: < -100 dBm @ 384 kSamp/sec 
FM Band Rejection 
>  60 dB 
Typical: 75 dB 
Measured: 80dB @ 145 MHz, Interferer @ 100.76 MHz 
 
 (1) 
High Sensitivity Mode, 
(2)
 Low Sensitivity Mode, 
(3)
 Noise Reduction 
All stated specifications and other product information provided in this document are subject to change without notice or obligation. 
 
Rev. 1 
02/2014