Sharpvision DW132671CAI Manuale Utente
Image Device
TV System
TV System
PAL
NTSC
Effective Pixels
Sensing Area
Scanning System
Sync. System
Horizontal Sync Frequency 15.625 kHz
Sensing Area
Scanning System
Sync. System
Horizontal Sync Frequency 15.625 kHz
15.734 kHz
Vertical Sync Frequency
50 Hz
60 Hz
Video Output
Gamma Consumption
AGC
S/N Ratio
White Balance
Electronic Shutter
BLC
Operation Frequency:
Line of Sight Range:
Receiving Sensitivity:
Video Codec:
Frame Rate:
Output Power:
Spread SPECTRUM:
Delay:
RF Bit Rate:
Operating Temperature
Storage Temperature
Minimum Illumination
Power Supply
Night vision distance
Waterproof rating
Audio
Viewing Angle
Gamma Consumption
AGC
S/N Ratio
White Balance
Electronic Shutter
BLC
Operation Frequency:
Line of Sight Range:
Receiving Sensitivity:
Video Codec:
Frame Rate:
Output Power:
Spread SPECTRUM:
Delay:
RF Bit Rate:
Operating Temperature
Storage Temperature
Minimum Illumination
Power Supply
Night vision distance
Waterproof rating
Audio
Viewing Angle
0Lux
DC10~32V
□8~10m □12~15m
DC10~32V
□8~10m □12~15m
Auto pairing:
1. Choose the channel that needs to be set up, and the monitor display the message
“PAIRING START 50” and a counter that counts down 50s.
2. Within the countdown, power the camera.
3. The monitor and cameras will synchronize themselves with each other after the
camera is powered for 5s.
For successful auto pairing, the picture appears. If pairing isunsuccessful, the
monitor displays the message “No Signal”. Repeat the pairing procedure. Manually pairing:
1. Choose the channel that needs to be set up, and the monitor display the message
“PAIRING START 50” and a counter that counts down 50s.
2. Press the pairing button on the power-on camera.
3. The monitor and cameras will synchronize themselves with each other.
For successful auto pairing, the picture appears. If pairing isunsuccessful, the
monitor displays the message “No Signal”. Repeat the pairing procedure.
1. Choose the channel that needs to be set up, and the monitor display the message
“PAIRING START 50” and a counter that counts down 50s.
2. Within the countdown, power the camera.
3. The monitor and cameras will synchronize themselves with each other after the
camera is powered for 5s.
For successful auto pairing, the picture appears. If pairing isunsuccessful, the
monitor displays the message “No Signal”. Repeat the pairing procedure. Manually pairing:
1. Choose the channel that needs to be set up, and the monitor display the message
“PAIRING START 50” and a counter that counts down 50s.
2. Press the pairing button on the power-on camera.
3. The monitor and cameras will synchronize themselves with each other.
For successful auto pairing, the picture appears. If pairing isunsuccessful, the
monitor displays the message “No Signal”. Repeat the pairing procedure.
IP69K
□ Yes □ No
□ 120° □ 92°
□ Yes □ No
□ 120° □ 92°
4Mbps
–20℃ ~ 70℃, RH95%MAX.
–30℃ ~ 80℃, RH95%MAX.
–20℃ ~ 70℃, RH95%MAX.
–30℃ ~ 80℃, RH95%MAX.
17dBm
FHSS
120ms
FHSS
120ms
-89dBm
MPEG4
PAL: 25f/s NTSC: 30f/s
MPEG4
PAL: 25f/s NTSC: 30f/s
Auto
2400-2483.5MHZ
120M
2400-2483.5MHZ
120M
Better than 48dB
Auto
Auto:1/60(NTSC)/1/50(PAL)～1/100,000 Seconds
Auto
Auto:1/60(NTSC)/1/50(PAL)～1/100,000 Seconds
1.0Vp-p, 75Ohm
0.45
Auto
0.45
Auto
4.6228mm×3.6112mm
2:1 Interlace
Internal
2:1 Interlace
Internal
CAMERA USER MANUAL
1/3" CMOS PC1089
728×488 pixels