LINSHENG INTERNATIONAL ENTERPRISE CO. LTD LS-RSK Manuale Utente
* systems control one actuator; two actuators or more actuators in synchronously or independently available;
* different remotes models and controller housing case for option.
* different remotes models and controller housing case for option.
1. Working Voltage:
10 ~14V DC
4. Controller Waterproof:
IP66~IP67
2. Frequency:
433.92 Mhz
5. Max Current:
20 A
3. Working Teperature
6. Static Current
0.06mA
INSTALLATION INSTRUCTIONS ---Remote Control System Series Kits (LS-RSK-2b)
Jumper S1 Open, Jumper S2 Closed
If the remotes lost, unavailable or broken, the switch on the board will be a
button for emergency.
button for emergency.
Press a time the actuators moving out, press 2 times quickly the actuators
retracting back.
retracting back.
A. New Remotes Program
3. Main Specifications:
E-mail: info@linsheng-auto.com ; Tel: +86-20-3916 5188 / 3916 5268; Fax: +86-20-62351526-0291; No.1, Hongbafang Industrial Park, Shilian Road, Guanchong, Shiji, Panyu District, Guangzhou (511450), China
-35 ~ 70 °C
Jumper S1 Open, Jumper S2 Open
Open the controller case and power the PCB to 12V
DC, press the switch on the board and the LED
lighting; then press any button of the remote to the
LED off.
DC, press the switch on the board and the LED
lighting; then press any button of the remote to the
LED off.
* At meanwhile, 2 remotes programmed at most.And
the third programmed remote will erase the first
one...
the third programmed remote will erase the first
one...
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
1. Remotes & Connection Guide:
2. Operation Instruction:
B. Automatic Operation
C. Manual Operation
D. Emergecy Manual Operation
Jumper S1 Open, Jumper S2 Open
Press"UP" a time, yellow and white wire output, actuator
moving out; press "UP" again to stop.
Press"DN" a time, blue and green wire output, actuator
retract; press "DN" again to stop.
moving out; press "UP" again to stop.
Press"DN" a time, blue and green wire output, actuator
retract; press "DN" again to stop.
If press "DN" when the actutor moving out,or if press "UP"
when the actutor retracting back; then the actutor will be
running in reverse directly and immediately.
when the actutor retracting back; then the actutor will be
running in reverse directly and immediately.
Jumper S1 Closed, Jumper S2 Open
Pressing and hold on the "UP" or "DN" button to
control the actuators moving out or retracking back.
control the actuators moving out or retracking back.
The actuators will not working if you not keep your
finger pressing onto the button.
finger pressing onto the button.