Versa Wireless Inc. VERSAX Manuale Utente
Operating Instructions
Mounting Guidelines
Installing the Versa
Programing
Testing
FCC Notice
The Versa is a compact wireless security
contact that can be installed on windows,
doors, and many other objects that open and
close. The Versa is equipped with a
Bluefield
TM
LED that glows BLUE when a
magnetic field comes within range of the
sensor during startup, and is also equipped
with a GREEN LED that flashes upon proper
initial startup and each time a signal is
transmited to the control panel. Signal
transmission occurs when a magnet is
brought within range or is moved out of range
of the sensor.
The Versa is also equipped with a RED LED
that will flash to indicate when the battery has
reached the Low Battery operating level for
the sensor. A low battery signal will also be
transmitted to the control panel.
Note: The Bluefield
TM
and Green signal LED’s
are operational when the cover is removed
and will operate for 3 minutes after the cover
has been installed. To restart these LED
functions, remove the cover. A tamper switch
has also been added for additional security.
The following steps describe general
guidelines for programming (learning) the
sensor into the alarm control panel memory.
For more details, please refer to the security
panel manufactures installation &
programming Instructions.
1. To remove the top of the Versa, use a
small flathead screwdriver and twist the
top cover off utilizing the recessed indents
on the sides of the sensor.
2. Set the panel to sensor learning mode.
3. Press and release the tamper switch on
the sensor until the panel responds.
4. Replace the top of the sensor.
5. Exit program mode.
Note: Always test in place before securing the
Versa to it’s final location
1. Select the desired location for the Versa
and magnet and insert the battery
(positive side up) into the base of the
Versa.
2. Hold the sensor up in the desired location
and temporally tape in place. Now hold
the magnet up to it’s desired location. If
the magnet is within range to trigger the
sensor, the Versa’s Bluefield LED arrow
will glow, ensuring proper placement.
3. If the Bluefield
TM
LED arrow does not glow,
position or orientate the magnet closer to
the Versa, or in some cases use a larger
magnet to bridge the gap.
4. Once the correct location of the magnet
has been found, fix the Versa and magnet
in place with the included 3M adhesive
tape.
When installing the Versa on a door, mount
the sensor on the frame and the magnet on
the door. This is to ensure that the sensor
receives the least amount of movement as
changing the orientation of a wireless device
can effect it’s performance.
• If possible, place the Versa within 100 ft.
of the security panel. While a transmitter
may have an open air range of 500+ feet,
a home and office environment can have
different effects on the transmitters range.
Sometimes a change in the Versa's
orientation can help enhance the wireless
transmission.
• Avoid mounting the Versa in areas where it
will be exposed to moisture or where the
operating temperature of 32 to 120ºF (0
to 50ºC) will be exceeded.
• Use spacers (not included) to keep the
Versa and magnet away from metal or
metallic surfaces such as foil wallpaper.
• Avoid mounting the Versa in areas with a
large quantity of metal or electrical wiring,
such as a furnace or utility room as this
can greatly affect the transmitting signal.
1. Put the control panel into sensor test
mode.
2. With the cover off (or during 3 minutes
after replacing the lid) hold the magnet up
to the Versa so that the Bluefield
TM
LED is
illuminated and then pull the magnet
away from the sensor. You will see the
GREEN signal LED flash indicating a
signal has been transmitted.
3. Listen for siren or keypad beeps to
determine appropriate response (refer to
the control panel installation instructions).
4. Exit sensor test mode.
Note: It is recommended that a system test be
performed per the Operation & User’s Guide
at least once a year.
Never handle the circuitboard antenna or by
pulling on it. Doing so will void the warranty.
Before mounting the sensor, verify that the
sensor mounting location provides good RF
communication to the panel. To verify, do the
following:
1. This device may not cause harmful
interference.
2. This device must accept any interference
that may be received, including
interference that may cause undesired
operation.
Changes or modifications not expressly
approved by Versa Wireless Inc. can void the
user’s authority to operate the equipment.
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en
compromettre le fonctionnement.
This device complies with FCC Rules Part 15.
Operation is subject to the following two
conditions: