Beijing Yueme Technology Co. LTD. ZPG01YM Manuale Utente
Turning on
for pairing
press and hold the camera
button for 2 seconds to turn on
the remote shutter for pairing.
Turing off
press and hold the camera bu-
ttonfor 3 seconds to turn off
the remote shutter.
Paired
the camera button lights blue
To be
paired
the camera button flashes blue
Sleep
mode
the remote shutter enters sleep
mode in 10 minutes if it fails to
pair, and the light will be dimmed
to 20% brightness and cease to
flash. It will not turn off during
sleep mode.
Exit sleep
mode
press the camera button to exit
sleep mode and restore 100%
brightness. The remote shutter
will pair to last connected device
as it exits sleep mode, and flash
blue if fails to pair.
Connection
lost
when your remote shutter loses
connection to your phone due to
long distance or other reasons,
it will enter sleep mode.
Pairing and
shooting
during
charging
the remote shutter works even
when it is charging.
Functions
Functions
Open the package, and mount the remote shutter onto
the rubber slot of the stick.
Mount the remote shutter:
Turn on your phone's Bluetooth feature, and locate
"XMZPG" for pairing. When the flashing stops and
turns solid blue, the pairing is completed.
Bluetooth pairing:
Hold the stick with its front facing up, and pull open
the phone holder by 90°, and rotate it by 180° to face
it towards you.
Rotate the phone holder to a fit position and extend
the rod, then fix your phone on the holder.
Open the phone holder
Fix your phone
Open the tripod from the bottom, and place it on a even
surface.
Set the tripod
Instructions:
Charging
the camera button flashes red
to indicate low power and require
immediate recharging; During
recharging, the red light is on,
and then turns blue once fully
charged.
Camera
the camera button lights blue
to indicate readiness for shoo-
ting.
Taking
photos
press the camera button.
Bluetooth
name
XMZPG
Principal: Xiaomi Inc.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
Address:Room 2057, Building1, 2 Cui Wei Road,
Hai Dian District, Beijing, China
Manufacturer: Beijing Yuemi Technology Co.,Ltd
changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation
party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation