Xinwei Electronic Industry. Co.Ltd.Fujian XW2016A24TX Manuale Utente

SMALL PARTS NOT FOR CHILDREN UNDER 3 YEARS. 
ADULT ASSEMBLY REQUIRED.

Remote Controller Battery: 6 x 1.5V AA

 

Charging Time: Approximately 120 minutes

Drone Battery: 800 mAh Li-po

Maximum Recommended Altitude 150 ft.

General Warnings 

Page 1

Contents and Remote Battery Installation 

Page 2

Charging Battery and Replacing Propellers

 

Page 3

Remote Overview 

Page 4

Operating Drone 

Page 5

Modes

Page 6

Tips and FCC Warning

Page 7

1. Slide open battery compartment

2. Install 6 “AA” batteries as shown in diagram

    shown above

3. Replace and close battery compartment

KEEP THIS INSTRUCTION MANUAL FOR REFERENCE  

Turn off the drone before charging. 

Connect the Battery Charge Cable to the Micro

USB port on the Drone.
Connect USB connector to power source.

Congratulations on your purchase of 

the Sharper Image Streaming 2.4 GHz 

DX-4 HD Video Drone. Get ready to

soar to new heights. Master the art of

drone flying and stunts with remote

control maneuverability. This

lightweight stunt drone will provide

hours of fun.

• Do not mix old and new batteries

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium)

batteries

• Insert batteries using the correct polarity. Do not short-circuit the supply terminal

• Only use manufacturer specified batter(ies), charger(s), and/or adapters, if

applicable, specified by the manufacturer

• Always use, replace, and recharge (if applicable) batteries under adult supervision

Note: The Battery Charge Cable will light up 

when it is charging the battery and turn off 

when the battery is fully charged. Charge time 

is approximately 120 minutes.

Light indicates

remote is on

Speed switch

Stunt button

Auto orientation

ON

Auto orientation

OFF

Auto take off

Auto land

ON/OFF

remote switch

Controls

flight direction

Throttle Joystick

Increases or decreases 

drone elevation

Spins drone

The drones range is approximately 400 feet or 150 feet of altitude:

• Read and be aware of all warnings found on Page 1.

• Maintain your desired elevation by using the Throttle.

• Push the Throttle joystick to right or left to spin the drone.

• Use the right joystick to move forward backwards, and side

to side.

• Review step 5 if your drone begins to drift.

• Drone will begin to blink when drone is paired to remote

and battery is low.

Follow this step if your drone begins to drift while take off or during 

flight.

• Drone drifts backwards: Press the forward Direction Trim

Button.

• Drone drifts forwards: Press the Backwards Direction Trim

Button.

• Drone drifts left: Press the Right Direction Trim Button.

• Drone drifts right: Press the Left Direction Trim Button.

• Drone spins clockwise (viewing drone from top): Press the

Left Spin Trim Button

• Drone spins counter-clockwise (viewing drone from top):

Press the Right Spin Trim Button

There are two ways to land the drone:

1. Press the Auto Land Button. The drone will slowly begin to land. If

the drone begins to drift, you can still control the drone’s

direction using the Multi Directional Button.

2. Slowly and carefully press the Throttle Joystick down until drone

lands. If the drone begins to drift, you can still control the drone’s

direction using the Multi Directional Button.

• Drone is designed to be flown indoors and

outdoors.

• Always make sure you have enough space to fly

drone.

• Always follow warnings, page 1.
Step 3 – Starting Drone

1. Making sure your remote is off, slide drone switch

to ON. Drone lights will begin to flicker.

2. Place drone on a flat even surface with clearance

according to diagram (Fig 1).

3. Turn remote on. Make sure the left stick (throttle)

is in a neutral position (stick is centered).

4. Push the stick up and then down.

5. A single tone indicates that the drone is paired.

Drone lights will  flicker rapidly then turn on 

permanently once paired. 

6. If pairing is unsuccessful, repeat steps 3-4.

1. Slowly and carefully press the Throttle Joystick

up. Drone will begin to elevate. You can

compensate for some of the drones drifting by

using the Multi Directional Button or by following

Step 5. You may need to practice this step

several times before successfully getting drone

into the air.

2. You can let go of the throttle once you get to your

desired elevation. The drone will engage its auto

Once you are comfortable flying the drone, use the Stunt Button to perform acrobatic stunts.

1. Hover the drone to at least above 10 feet.

2. Press the Stunt Button. You will hear beeping coming from the remote

3. Move the Multi Directional Button to the desired direction that you would like the drone to flip

Once you are comfortable flying the drone, use the Auto Take Off Button for an easy take off. 

1. Turn remote ON

2. Pair remote to drone: Bring the Throttle all the way up then bring it all the way down, remote will beep once paired.

3. Press the Auto Take Off Button. Drone will begin to elevate. Drone will level out around 5 ft off the ground and

automatically enter into auto hover.

4. Now the drone can be controlled using both the throttle and the multi-directional joystick.

• Auto Orientation default setting is off. To enter this mode press Auto Orientation “+” button.  Remote

will beep twice.

• After drone is successfully paired, the 2 white LED lights toward orientation will be the original forward orientation, when drone

is in auto orientation mode, the drone will orient to the user (remote), no matter what direction the drone is facing. Pushing the

right stick up will send the drone away from the user, pushing it to the right will move the drone right, etc.

• Remote will beep every 6 seconds to indicate the drone is in Auto Orientation mode.

• To exit mode, press the “-“ button. Remote will sound 1 long beep indicating that it has exited Auto

Orientation mode.

• Make sure you have achieved level, balanced flight, where the drone is neither climbing nor descending.This mode allows you

to safely and slowly land your drone without having to control the speed.  It is done for you automatically.

• The ideal auto landing height is 25-30 ft.

• Press the “v“ button to trigger auto land. Remote will beep continuously until you exit the auto land mode.

• To steer the drone during landing, use the right control until drone has reached the ground.

• Press the “v“ button again to exit auto landing mode.

• Taking a picture- press camera icon on app once to take a picture. 4 main lights will blink once to indicate photo has been

taken.

• Creating video- press video icon on app once to take a video. Main lights will blink continuously indicating video is being

recorded. Press the video icon on app again to stop recording.

• Lights will go solid (stop blinking) when video recording has stopped.

NOTE: Pictures and video camera cannot be taken at the same time. 

Connect the USB Charge

Cable to the Drone

Insert the USB

Charge Cable

into a USB

power source

There is a risk of fire and personal injury if Li-Po

battery is punctured, damaged or misused

• Never expose battery to extreme temperatures

or moisture

• Do not subject battery to strong impacts

• Always keep battery away from flammable

materials

• Only use manufacturer specified batter(ies),

charger(s), and/or adapters, if applicable,

specified by the manufacturer

• Battery is not serviceable

• Let battery cool to room temperature before

charging

• While charging, never leave battery unattended

• Recycle or dispose of battery according to federal,

   

state and local laws

 

1. Read all warnings and instructions.

2. Install remote batteries, page 2.

3. Make sure that drone and remote are powered off.

4. Install drone holder.

5. Charge batteries, page 3.

•

Not recommended for children under 12 years of age. As with all electrical products, precaution

should be observed during handling and use to reduce the risk of electrical shock.

•

Adult supervision is required at all times.

•

Before each use, an adult should review the product and battery to determine that no damage

or 

hazards exist.

•

Do not allow anything to intentionally make contact in any way with spinning propellers.

• Prevent contact with spinning blades by turning off remote prior to handling drone.

•

Keep drone away from power lines, buildings, trees, public areas, and any other potentially

hazardous areas.

•

Do not operate in rain, heavy wind, and or any type of severe weather.

•

Do not land drone on wet surfaces.

•

Never touch or allow others to touch drone while it is flying.

•

Always turn drone off when it is not in use.

•

Always fly drone in large open areas.

•

Never fly drones above or near people, sudden changes in wind or other conditions could lead to

unexpected crashes.

•

Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and

property rights of others.

•

The drone shall never be modified or used for anything except its intended purpose.

• Do not crash drone into sand or dirt. Drone gears may become clogged

• When first learning to fly, practice lifting off and hovering

• Stay several feet from walls and buildings

• Always press throttle all the way down after crashing or when something gets stuck in propellers

• Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.

• Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others.

• The drone shall never be modified or used for anything except its intended purpose.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s 

authority to operate the equipment.

When remote switch is turned on, the remote light does not illuminate:

1)

Check that batteries in the remote are installed correctly OR

2)

Replace with new batteries

During drone flight, the remote LED is flashing:

1)

Remote batteries are low; replace them with new batteries

Drone and remote properly pair, but the drone will not lift-off:

1)

Drone battery needs charging. Use the USB Charge Cable to connect the drone to

power source.

After trimming the drone, the drone flight is very unstable and cannot fly properly:

1)

One or more blades are most likely damaged;

2)

Turn off the drone and remote.

3)

Replace with the proper number replacement blade and try flying again.

After impact, the drone is unstable:

1)

Put the left remote control lever to the left bottom and put the right  remote control lever

to the right bottom at the same time which connected to the drone (diagram to right).

2)

If the above does not resolve the issue, reboot the drone and controller and pair again.

Remote Controller and Drone can not be paired:

1)

Check Point: Remote Controller must be closed to Drone, not exceed 4 meters.

Note: If there are 2 sets of Drones within 4 meters for Pairing, you must pair one successfully before pairing the second set.

, 

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna,

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. 

© Sharper Image. All Rights Reserved. 

SHARPER IMAGE® name and logo are registered trademarks manufactured and marketed by MerchSource, LLC under license. All other logos and 

trademarks are proprietary to their respective owners. The artwork and design of this package are protected by US copyright law and may not be 

reproduced, distributed, displaced, published or used for any purpose without prior written permission. Altering, removing or reproducing any of the 

trademark or copyright notices on this package is not permitted.

©2016 MerchSource, LLC. All rights reserved.

Distributed by MerchSource, LLC, Irvine, CA 92618.

PATENT PENDING

Printed in China

This device  complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause 

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

DIRECTIOIN

TRIM

Always be mindful of others privacy and do not 

record video or take images of others without 

their consent. Check and comply with your 

federal, state and local laws regarding privacy. 

4

1. Follow diagram

2. Remove screw from top of Propeller

3. Remove broken Propeller and replace

with new Propeller

4. Make sure you installed the correct

blade. Each blade has a number

written on it. Match the blades with

the corresponding number on the

drone

5. Insert screw into top of Propeller

1. Press the connect to Wi-Fi

button

2. Follow the on screen

instructions

1. Press the Stream Button to

begin streaming

2. Press the Album Button to

review pictures and videos

Go to your app store on your smart phone and download the “360 Flight” application. 

AUTO

ORIENTATION

LAND

DIRECTION

TRIM

TAKE

OFF

4 

H
M
L

AUTO

ORIENTATION

LAND

DIRECTION

TRIM

TAKE

OFF

4 

H
M
L

AUTO

ORIENTATION

LAND

DIRECTION

TRIM

TAKE

OFF

4 

H
M
L

Before each flight pair the remote with the drone:

1. Turn your drone on and place on a flat, level surface

2. Turn on the remote on and move the left joystick up, then down

3. The beep will indicate successful pairing

4. Repeat steps 1 and 2 if necessary

• White lights indicate the front of the drone

• Red lights indicate the back of the drone

• Not applicable in auto-orientation mode

Practice flying your drone below 10 feet and at low speeds until comfortable with all

controls to avoid unncessary damage or injury

• Left joystick:

 

 

• Up/Down controls elevation

• Left/Right controls spin

• Right joystick: controls flight direction

• Direction Trim: use to eliminate drift

To cut power to drone, move left joystick to down position 

• Drone must be charged before each use (USB Charge Cable included)

• Indicator light will turn off once fully charged

• Install batteries in remote

Trim controls

are used to

minimize drift

Insert antena through hole at the base of the 

Smart Phone Mount.

Align hole on Mount with hole in antena. Insert 

screw to secure Mount to remote. 

Carefully slide phone into Mount by pulling up 

on top of Mount. Adjust angle accordingly.

Fig. 1

v.05

Caution: To Maintain the compliance with the RF exposure guideline, place the Drone at least 20 cm from nearby persons.