U-tec Group Inc. UL1 Manuale Utente
Perform Better Fingerprint
FAQ
Use UL1 without Smartphone
- 2 -
1.
Reset UL1 and Register Admin Key.
1) Pin the reset button for 3 seconds. LED will blink blue
seconds.
2) Tap the Black Key Fob (Admin Key) on reader. LED will
flash green.
3) Tap the Black Key Fob again. LED will flash green.
4) Now the Black Key Fob has been registered as the
Admin Key.
seconds.
2) Tap the Black Key Fob (Admin Key) on reader. LED will
flash green.
3) Tap the Black Key Fob again. LED will flash green.
4) Now the Black Key Fob has been registered as the
Admin Key.
2.
Enter Register Mode.
1) Tap the Admin Key. UL1 will enter register mode. LED
will blink blue.
2) Now you can register new users by fingerprint or key
fob.
will blink blue.
2) Now you can register new users by fingerprint or key
fob.
- 5 -
3.
Register a Fingerprint User.
1) Press the finger on the sensor. LED will flash green.
Repeat the process for 3 times.
2) Once the fingerprint has been succussfully registered,
LED will blink blue as waiting for the next action.
Register a Key Fob User.
1) Pick a regular key fob as the User Key.
2) Tap it on the reader. LED will flash green. Repeat the
process for 2 times.
3) Once the key fob has been succussfully registered,
LED will blink blue as waiting for the next action.
Repeat the process for 3 times.
2) Once the fingerprint has been succussfully registered,
LED will blink blue as waiting for the next action.
Register a Key Fob User.
1) Pick a regular key fob as the User Key.
2) Tap it on the reader. LED will flash green. Repeat the
process for 2 times.
3) Once the key fob has been succussfully registered,
LED will blink blue as waiting for the next action.
4.
Exit Register Mode.
When LED is blinking blue, tap the Admin Key or wait 10
seconds to exit the register mode. LED will turn off.
seconds to exit the register mode. LED will turn off.
Notes:
1) Whenever LED flash red, it means a failure has
occured.
1) Whenever LED flash red, it means a failure has
occured.
2) If a failure has occurred, the current process will
be reset. Start over the process.
be reset. Start over the process.
3) UL1 can store 99 fingerprints & 99 key fobs.
- 6 -
- 3 -
- 4 -
- 7 -
1. What type of door does UL1 compatible with?
UL1 is a latch lock that compatible with most of American doors
(
(
thickness 33-50mm
). Please refer to Page 4 on Installation Guide
for details.
UL1 cannot be installed on glass doors.
UL1 cannot be installed on glass doors.
2. Does UL1 support left-handed/right-handed opening?
Yes. When installing UL1, adjust its direction to your preference.
3. Installtion completed, but there is no power on UL1.
1) Check the direction of the batteries. Positive pole should
towards the latch.
2) On Internal Assembly, Check if the wire is connected to the
receiver correctly.
towards the latch.
2) On Internal Assembly, Check if the wire is connected to the
receiver correctly.
4. What’s the difference between App Mode and Standalone
Mode?
App Mode:
Use U-tec App (iOS&Android) via Bluetooth to control lock
(including register and use fingerprint access & key fob access,
check activity log, set lock status, clone user information, etc). If
you have a Ultraloq Bridge, you can control lock remotely.
App Mode:
Use U-tec App (iOS&Android) via Bluetooth to control lock
(including register and use fingerprint access & key fob access,
check activity log, set lock status, clone user information, etc). If
you have a Ultraloq Bridge, you can control lock remotely.
Standalone Mode:
You can register and use fingerprint access & fey fob access
directly on the lock. No smartphone required and lock cannot be
controlled remotely.
You can register and use fingerprint access & fey fob access
directly on the lock. No smartphone required and lock cannot be
controlled remotely.
- 8 -
Please check www.u-tec.com for specific
warranty details and limitations.
1. Follow the above illustration to register your fingerprint
properly. Make sure your finger is flatly placed at the
center of the reader for a better identification.
center of the reader for a better identification.
2. It is recommended that each user registers two or more
fingerprints. When registering, place your finger at the
center with the same gesture for three times.
center with the same gesture for three times.
3. Please note that dry, wet, oily or dirty fingers may affect
the fingerprint identification.
4. Avoid the callus, peeling or injured finger to ensure the
registration and identification successful.
5. In case of low recognition rate, please delete the original
registered fingerprint and register it again.
Ultraloq UL1
Smart Lock
User Guide
(V1.0)
Warranty Statement
Fingerprint Sensor
Key Fob Reader
Key Fob Reader
Reset
LED Light
Fingerprint Sensor
Key Fob Reader
Use UL1 with Smartphone
1. Scan the QR code to download the U-tec app, or search “U-tec”
in App Store (iOS) and Google Play (Android).
2. Open the app, register U-tec account, and log in the account.
3. Reset UL1, turn on Bluetooth on the phone, stay near the lock,
and search the lock in the app.
and search the lock in the app.
4. Add the lock in the app and start to use it.
* UL1 has another independent
Standalone Mode that can be
used without smartphone. Please check page 5 and page 6 for
details.
details.
* UL1 has to be reset every time to switch between two
modes. *
modes. *
* You can only use basic functions in Standalone Mode (Register
and use fingerprint access & key fob access).
and use fingerprint access & key fob access).
Use UL1 without Smartphone
Need Help? Contact Customer Support.
· Visit www.u-tec.com/support
· Email support@u-tec.com