Fantem Technologies Co. Ltd FT101 Manuale Utente
CUBE
Cube.
1
Familiarize yourself with your Cube.
2
Oomi Cube is an intelligent gateway controller, it is not only a Z-Wave
Controller but also integrates the other wireless technology and Sensors,
e.g. NFC, Wi-Fi, Bluetooth, Webcam, PIR Sensor, temperature Sensor, light
Sensor and so on. Just one intelligent device will give you the perfect smart
home.
Quick start.
3
Since Oomi Touch can be acted as a window for the Cube, so pairing your
Cube with the Oomi Touch is needed, the following instructions will tell you
how to pair it.
Add/remove a Z-Wave device.
4
After your Cube is complete all the pairing with the Touch, now you can use
the Touch to add a Z-Wave device to your Cube.
This is a sample of adding the Oomi Plug:
Above you'll see a basic run-down of this system in action.
Please refer: http://www.oomi.com/
This tablet works with Android and is extremely basic, working with a
skinned version of Android and controls that work with the Oomi Cube
directly.
The Oomi Plug allows you to wirelessly control power output from any
socket. It's like plugging a mid-point between your normal outlet and the
device you'd like to use. There's also a USB power port for your mobile
device.
Of course, you can also add other Oomi’s Z-Wave devices (e.g. Oomi’s Bulb,
MultiSensor, Dimmer, Door/ Window Sensor, Streamer and so on) into the
network with the same operation. After they are added into the network,
you will be very conveniently to get their status and easily to
control/manage them on the Touch’s screen.
1.
2.
3.
Keep your Cube is powered on.
Wi-Fi connection between your Cube and Touch. Turn on the WLAN of
your Touch and then find out the Wi-Fi SSID of the Cube, select it and
then type the password in, after a few seconds, your Oomi Touch’s
WLAN would be connected to the Cube’s Wi-Fi network, if not, repeat
the steps above.
NFC connection between your Touch and Cube. This connection is very
simple, you just need to take your Touch near to the Cube and then find
out the NFC point on the Cube. The NFC point is marked with a yellow
colour cycle. Just touch it with your Oomi Touch. You will see the Status
LED on Cube is changed to purple colour and then the purple LED dims
on and then off. About a few seconds later, your Cube would complete
the NFC pairing. You will see the Touch’s screen will pop up a Cube
picture as the figure below and then you can follow the UI guidelines to
configure the Cube. If you don’t see anything comes out from the
screen, please repeat the steps above.
1.
2.
3.
Power on the Oomi Plug.
Take the Oomi Cube near to the Oomi Plug and then let the Oomi Touch
touches the NFC point of the Plug once.
You will see the Status LED on the Oomi Plug is changed to purple
colour and then the purple LED dims on and then off. About a few
seconds, you will see an icon of the Plug is popped up on the screen of
the Touch, see the figure below, click the icon entering into the control
page and following the UI guidelines to configure or manage the Plug
node.
1.
2.
3.
4.
Power on the Oomi Plug.
Click the “Exclude/Remove” button on your Touch’s app.
Take the Oomi Touch near to the Oomi Plug and then let the Oomi
Touch touches the NFC point of the Plug once.
You will see the Status LED on the Oomi Plug is changed to purple
colour and then the purple LED dims on and then off. About a few
seconds, you will see the Plug’s LED is blinking slowly and the original
Plug icon is removed from the Touch’s app.
Plug the DC 5V Adapter into the power socket and then connect the
Adapter’s output port to the input port of Cube. You will see the orange LED
will be on, after a few seconds, the LED’s colour is changed from orange to
green indicates the setup of system is successful. Otherwise, if the red LED
lights up, means the setup is failed, just repeat the steps above.
In the next step, connect your Cube to the ADSL Modem or your home
router with a network cable provided, as show the figure below:
Note: If your home has the Wi-Fi signal, the Cube also can be connected to
the internet network via Wi-Fi connection. How to use the Wi-Fi connection,
you can follow steps would be guided by the Oomi Touch.
Install your Cube.
Add a Z-Wave device into your Cube.
Remove a Z-Wave device from your Cube.