Transition Networks CETTF1015-105 Dépliant
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2010 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
CETTF10xx-x0x
Specifications
Standards
IEEE Std. 802.3, 10BASE-T; 10BASE-FL
4-position Switch
Fiber Port: Enables / disables network traffic on the
fiber port; (Up = enabled)
Copper Port: Enables / disables network traffic on
the copper port; (Up = enabled)
AutoCross™: Enables / disables AutoCross™
function; (Up = enabled)
Link Pass Through: Enables / disables Link Pass
Through function; (Up = enabled)
fiber port; (Up = enabled)
Copper Port: Enables / disables network traffic on
the copper port; (Up = enabled)
AutoCross™: Enables / disables AutoCross™
function; (Up = enabled)
Link Pass Through: Enables / disables Link Pass
Through function; (Up = enabled)
3-position Jumper
Hardware: Converter mode is determined by
4-position switch settings
Software: Converter mode is determined by most
recently saved on-board microprocessor setting
4-position switch settings
Software: Converter mode is determined by most
recently saved on-board microprocessor setting
Status LEDs
PWR (Power): On for normal operation;
LKF (Link Fiber): Steady LED indicates good fiber
link and normal operation;
RXF (Receive Fiber): Flashing LED indicates data
reception on fiber link;
LKC (Link Copper): Steady LED indicates good
copper link and normal operation;
RXC (Receive Copper): Flashing LED indicates data
reception on copper link
LKF (Link Fiber): Steady LED indicates good fiber
link and normal operation;
RXF (Receive Fiber): Flashing LED indicates data
reception on fiber link;
LKC (Link Copper): Steady LED indicates good
copper link and normal operation;
RXC (Receive Copper): Flashing LED indicates data
reception on copper link
Dimensions
Width: 0.86" [22 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]
Power Consumption
2.3 Watts
Environment
See chassis specifications
Shipping Weight
1 lb. [0.45 kg]
Regulatory Compliance
EN55022; EN55024; EN61000; CE Mark
Warranty
Lifetime
point system™ slide-in-module media converter
Integrate mixed cabling
environments in either
switched or shared
Ethernet networks.
switched or shared
Ethernet networks.
Connect legacy 10BASE-T
devices to a fiber based
cabling infrastructure.
cabling infrastructure.
Ordering Info: Class A
CETTF1011-105
10BASE-T (RJ-45)
[100 m/328 ft.]
to 10BASE-FL 850 nm MM (ST)
[2 km/1.2 mi.] Link Budget: 13.5 dB
CETTF1013-105
10BASE-T (RJ-45)
[100 m/328 ft.]
to 10BASE-FL 850 nm MM (SC)
[2 km/1.2 mi.] Link Budget: 13.5 dB
CETTF1027-105
10BASE-T (RJ-45)
[100 m/328 ft.]
to 10BASE-FL 1300 nm MM (ST)
[5 km/3.1 mi.] Link Budget: 13.5 dB
CETTF1012-105
10BASE-T (RJ-45)
[100 m/328 ft.]
to 10BASE-FL 1310 nm SM (ST)
[20 km/12.4 mi.] Link Budget: 7.0 dB
CETTF1014-105
10BASE-T (RJ-45)
[100 m/328 ft.]
to 10BASE-FL 1310 nm SM (SC)
[20 km/12.4 mi.] Link Budget: 15.0 dB
CETTF1022-105
10BASE-T (RJ-45)
[100 m/328 ft.]
to 10BASE-FL 1310 nm SM (ST)
[40 km/24.9 mi.] Link Budget: 19.0 dB
CETTF1015-105
10BASE-T (RJ-45)
[100 m/328 ft.]
to 10BASE-FL 1310 nm SM (SC)
[40 km/24.9 mi.] Link Budget: 14.0 dB
Single Fiber Products
Recommended use in pairs (see page 18)
Recommended use in pairs (see page 18)
CETTF1029-105
10BASE-T (RJ-45)
[100 m/328 ft.]
to 10BASE-FL 1310 nm TX / 1550 nm RX
single fiber SM (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
CETTF1029-106
10BASE-T (RJ-45)
[100 m/328 ft.]
to 10BASE-FL 1550 nm TX / 1310 nm RX
single fiber SM (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
Extend Network Distance
Two 10BASE-T to 10BASE-FL Media
Converters used back-to-back extend the
distance between two 10BASE-T devices
up to 5 km (3.1 mi.) using multimode fiber,
up to 40 km (24.9 mi.) using single mode
fiber without a repeater, or up to 20km
using single strand single mode fiber.
Converters used back-to-back extend the
distance between two 10BASE-T devices
up to 5 km (3.1 mi.) using multimode fiber,
up to 40 km (24.9 mi.) using single mode
fiber without a repeater, or up to 20km
using single strand single mode fiber.
Connect Unlike Devices
Connect your workgroup to a distant server
or a central switch; or extend distances
between like and unlike devices in either
full or half-duplex modes.
or a central switch; or extend distances
between like and unlike devices in either
full or half-duplex modes.
AUTO CROSS LINK PASS THRU LINK RESTORE
AUTO
UPGRADE
REMOTE FIRMWARE
10BASE-T to 10BASE-FL
SINGLE
FIBER
FCC & CISPR Class A devices comply with
radiated emissions standards for commercial
applications in the United States (FCC Class A)
and Europe (CISPR Class A).
radiated emissions standards for commercial
applications in the United States (FCC Class A)
and Europe (CISPR Class A).
FCC & CISPR Class B devices comply with
radiated emissions standards for residential
applications in the United States (FCC Class B)
and Europe (CISPR Class B).
radiated emissions standards for residential
applications in the United States (FCC Class B)
and Europe (CISPR Class B).
see also:
Ethernet 10BASE-T to 10BASE-FL Stand-Alone Media Converters
Ethernet Copper to Fiber Media Converter
Features (both Class A & B)
Can be used with any Point System™ Chassis
AutoCross™
Link Pass Through
Automatic Link Restoration
Remote Firmware Upgrade