Transition Networks SSDTF1029-121 SSDTF1029-121-NA Dépliant
Codici prodotto
SSDTF1029-121-NA
Stand-Alone
Ordering Information
SSDTF1011-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 850nm multimode (ST)
[2 km/1.2 mi.] Link Budget: 13.5 dB
SSDTF1013-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 850nm multimode (SC)
[2 km/1.2 mi.] Link Budget: 13.5 dB
SSDTF1027-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1300nm multimode (ST)
[5 km/3.1 mi.] Link Budget: 13.5 dB
SSDTF1012-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
1310nm single mode (ST)
[8 km/5 mi.] Link Budget: 7.0 dB
SSDTF1022-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1310nm single mode (ST)
[15 km/9.3 mi.] Link Budget: 10.0 dB
SSDTF1014-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1310nm single mode (SC)
[20 km/12.4 mi.] Link Budget: 16.0 dB
SSDTF1015-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1310nm single mode (SC)
[40 km/24.9 mi.] Link Budget: 30.0 dB
SSDTF1016-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1310nm single mode (SC)
[60 km/37.3 mi.] Link Budget: 33.0 dB
SSDTF1017-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1550nm single mode (SC)
[80 km/49.7 mi.] Link Budget: 29.0 dB
Single Fiber Products
SSDTF1029-120
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1310nm TX /1550nm RX single fiber SM
(SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SSDTF1029-121
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1550nm TX/1310nm RX single fiber SM
(SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SSDTF1029-122
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1310nm TX/1550nm RX single fiber SM
(SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
SSDTF1029-123
Twisted Pair (RJ-48)
[1.5 km/0.9 mi.]
to 1550nm TX/1310nm RX single fiber SM
(SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
Device
Device
Provide Campus Interconnects
SSDTFx0xx-12x
SSDTFx0xx-12x
stand-alone network interface device
Features
4
Remote unit in-band management
4
Local or Remote Loopbacks on copper
or fiber in software mode
4
Loopbacks via test set
4
Converts the copper ports on T1/E1
devices, such as a PBX or T1/E1
Router, to multimode or single
mode fiber
4
Switch selectable RJ-48 connectors
for T1 or E1
4
Jitter attenuators optimize Bit Error
Rate (BER) performance
4
Network debug procedures make BER
testing more convenient
4
Built-in troubleshooting with the
addition of a selectable TAOS
(Transmit All Ones) switch on the fiber
and copper interfaces allows the
network engineer to test all T1/E1
equipment on that network segment
and ensure the network link
4
Dry Relay Contacts enable the device
to be tied into a separate alarm circuit
commonly found in a T1/E1 twisted
pair environment. Contacts will be
activated on loss of power or loss of
fiber link.
4
LED provides Alarm Indication
Signal (AIS)
4
Can be used with fractional
T1/E1 circuits
4
Report converter status
• Copper & Fiber Link status
• Copper & Fiber Link status
• Hardware switch settings: LBO, AIS
Copper, AIS Fiber, HW/SW
• AIS detected Copper & Fiber
• Model Number
• Copper & Fiber Connector
4
Remote commands:
• Loopback Copper & Fiber
• AIS transmitted on Fiber on loss of
Copper link
• AIS Transmitted on Copper on loss
of Fiber link
4
Extend PRI over fiber
T1/E1
see also:
T1/E1 Point System™ Slide-In-Module NID
Remotely Managed T1/E1 NID (Network Interface Device)
T1/E1 Copper to Fiber with Remote In-Band Management
4
Remote management in a stand-alone
device When used in conjunction with a
managed Point System™ chassis, this
stand-alone unit can be managed remotely.
managed Point System™ chassis, this
stand-alone unit can be managed remotely.
4
The Remotely Managed T1/E1 copper to
fiber media converter will provide a solution
for users who desire to extend their T1/E1 or
PRI circuits over fiber and remotely manage
them “in-band” from admin locations.
fiber media converter will provide a solution
for users who desire to extend their T1/E1 or
PRI circuits over fiber and remotely manage
them “in-band” from admin locations.
Specifications
Standards
ITU-T, ANSI, AT&T, ETSI
3-position Jumper
Hardware: mode is determined by 4-position
switch settings
Software: mode is determined by most recently
saved on-board microprocessor settings.
Status LEDs
PWR (Power): Steady green LED indicates
connection to external AC power
SDC (Signal Detect/Copper): On indicates twisted
pair link is up
SDF (Signal Detect/Fiber): On indicates fiber
link is up
Dimensions
Width: 3.25” [82 mm]
Depth: 4.8” [122 mm]
Height: 1.0” [25 mm]
Power
External AC/DC provided; 12V DC; 0.5A; unregulated;
standard;
UL listed
Environment
0 – 50°C,
5% – 95% humidity (non-condensing),
0 – 10,000 ft.
Shipping Weight
2 lbs. [0.90 kg]
Safety Compliance
Wall Mount Power Supply:
CSA certified
Regulatory Compliance
CISPR/EN55022 Class A;
FCC Class A; CE Mark
Warranty
Lifetime
Devices must be used in pairs. Typically installation will include a chassis card
[CSDTF, pg 59] installed in the Point System™ locally and a stand-alone
device installed at the remote location.
[CSDTF, pg 59] installed in the Point System™ locally and a stand-alone
device installed at the remote location.
Optional Accessories (sold separately)
Wide Input (18 – 72 VDC) Power Supplies
SPS-24602-PS
Piggy Back Power Supply
SPS-2460-SA
Stand-Alone Power Supply
Mounting Options
E-MCR-05
12-Slot Media Converter Rack
RMS19-SA4-01
4-Slot Media Converter Shelf
WMBD
DIN Rail Bracket 5.0” [127 mm]
WMBD-F
DIN Rail Bracket (flat) 3.3” [84 mm]
WMBL
Wall Mount Bracket 4.0” [102 mm]
WMBV
Vertical Wall Mount Bracket 5.0” [127 mm]
T1/E1 Copper to Fiber with Remote In-Band Management