Transition Networks SPS-2460-PS Dépliant
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2010 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
Specifications
Input Voltage
24 – 60VDC; 24 – 42VMRS
Isolation Voltage
(Dielectric withstand) Meets IEC 950 for one minute
1500 VAC: Output/Input
1500 VAC: Input/Safety GND
1500 VAC: Output/CASE
1500 VAC: Output/Input
1500 VAC: Input/Safety GND
1500 VAC: Output/CASE
Output Voltage
12.25 VDC
Output Current
1.0A
Load Regulation
±5% at 10% load to full rated load
Over Load Protection
(OLP)
When the average power rating exceeds 125%-150% of maximum
power, output voltages reduced to a safe dissipation level; protects
against short circuit of any output
against short circuit of any output
No Load Protection
No damage to power supply when operating at no load
Transient Protection
No voltage spike at power-on, power-off, or power failure
Power Distribution
+12.25VDC at 1.0A maximum
Power Consumption
3 Watts max. @ 24VDC input, 12.25VDC output
Efficiency
80% (typical)
Noise and Ripple
±40mV peak-to-peak of output voltage (typical)
MTBF
Greater than 250,000 hours with typical load operating
at 25°C temperature (calculated according to MIL-HDBK-217E)
at 25°C temperature (calculated according to MIL-HDBK-217E)
Regulatory Compliance
CISPR/EN55022; Class A; FCC Class A
Dimensions
SPS-2460-SA:
Width: 3.75" [95 mm]
Depth: 3.1" [79 mm]
Height: 1.0" [25 mm]
Width: 3.75" [95 mm]
Depth: 3.1" [79 mm]
Height: 1.0" [25 mm]
SPS-2460-CC:
Width: 4.5" [114 mm]
Depth: 3.1" [79 mm]
Height: 1.0" [25 mm]
Width: 4.5" [114 mm]
Depth: 3.1" [79 mm]
Height: 1.0" [25 mm]
SPS-2460-PS:
Width: 4.5" [114 mm]
Depth: 3.4" [86 mm]
Height: 1.0" [25 mm]
Width: 4.5" [114 mm]
Depth: 3.4" [86 mm]
Height: 1.0" [25 mm]
Shipping Weight
1 lb. [0.45 kg]
Environment
Operating: -20°C to +65°C
Storage: -40°C to +85°C
Humidity: 5 – 95% non-condensing
Altitude: 0 – 10,000 ft.
Storage: -40°C to +85°C
Humidity: 5 – 95% non-condensing
Altitude: 0 – 10,000 ft.
Warranty
Lifetime
SPS-2460-SA
Stand-Alone Power Supply
Stand-Alone Power Supply
SPS-2460-CC
Piggy-Back Power Supply
Piggy-Back Power Supply
Ordering Info
SPS-2460-CC
Piggy-Back
For use with: Non-Point System™
stand-alone media converters
3.0" wide (E-TBT-FRL-05;
E-100BTX-FX-05; etc.)
For use with: Non-Point System™
stand-alone media converters
3.0" wide (E-TBT-FRL-05;
E-100BTX-FX-05; etc.)
SPS-2460-PS
Piggy-Back
For use with: Point System™ stand-alone
media converters 3.25" wide
(SBFTF1011-100; SGETF1013-100, etc.)
For use with: Point System™ stand-alone
media converters 3.25" wide
(SBFTF1011-100; SGETF1013-100, etc.)
SPS-2460-SA
Stand-Alone
For use with: All stand-alone media
converters; Single-Slot Point System™
Chassis; Dual-Slot Point System™ Chassis
For use with: All stand-alone media
converters; Single-Slot Point System™
Chassis; Dual-Slot Point System™ Chassis
Transition Networks’ wide input ex-
ternal power supplies allow you to
provide a wide range of input voltages
to power your stand-alone converters
and chassis. Input voltages of 24 –
60VDC and 24 – 42VRMS allow for in-
stallation of any of Transition’s stand-
alone media converters in most
industrial, telecom and commercial
applications, as well as HVAC and
building controlled environments.
ternal power supplies allow you to
provide a wide range of input voltages
to power your stand-alone converters
and chassis. Input voltages of 24 –
60VDC and 24 – 42VRMS allow for in-
stallation of any of Transition’s stand-
alone media converters in most
industrial, telecom and commercial
applications, as well as HVAC and
building controlled environments.
Multiple form factors allow flexibil-
ity to meet your application. The
stand-alone form factor can be used
with all Transition stand-alone media
converters as well as the single-slot
and dual-slot Point System™ Chas-
sis. The piggy back form factor allows
the power supply to attach directly to
the converter and eliminate the power
cable commonly found between the
power supply and the converter. Once
the piggy back supply is attached to
the converter, the combined assembly
is much easier to wall mount or attach
to Din Rail environments than using a
separate supply.
ity to meet your application. The
stand-alone form factor can be used
with all Transition stand-alone media
converters as well as the single-slot
and dual-slot Point System™ Chas-
sis. The piggy back form factor allows
the power supply to attach directly to
the converter and eliminate the power
cable commonly found between the
power supply and the converter. Once
the piggy back supply is attached to
the converter, the combined assembly
is much easier to wall mount or attach
to Din Rail environments than using a
separate supply.
SPS-2460-xx
stand-alone media converter power supplies
Wide Input External Power Supplies
Accessories
Extended Temperature Power Supply
SPS-2460-PS
Piggy-Back Power Supply
Piggy-Back Power Supply