Gefen EXT-HDKVM-LANRX Dépliant
Extend and Distribute HDMI, USB, RS-232, IR, and 2-way audio
over a Local Area Network using any combination of HDMI, DVI,
and VGA Sender and Receivers
The Gefen HD KVM over IP extends HDMI, USB, 2-way analog audio, RS-232, and IR, over
a Gigabit Local Area Network. Resolutions up to 1080p Full HD and 1920 x 1200
(WUXGA) are supported. The Senders and Receivers can be automatically or manually
configured to unique IP addresses to allow the connection of multiple units to the same
network. Multiple Receiver units can simultaneously connect to any Sender unit within the
network including the Gefen KVM over LAN products with HDMI, DVI, or VGA video, to
create a virtual crosspoint matrix of just over 65,000 Sender and Receiver units total,
depending on the network bandwidth and number of ports on the network switch (see Note).
When using HDCP-encrypted content, only HDMI Senders and Receiver units can accept
and display the content. Each Receiver unit has a built-in Ethernet switch and two additional
RJ-45 Ethernet ports to allow for the connection of computers and other IP-enabled devices.
USB 2.0 data rates up to 480 Mbps are supported in addition to backward-compatibility
with USB 1.1. Each Receiver unit provides two USB ports with up to 500mA current draw per
connector, providing access to keyboard, mouse, and other compatible devices.
Bi-directional analog audio capability allows audio to be transported between the Sender
and the Receiver units. The built-in mic pre-amp on the Receiver unit ensures compatibility
with a variety of microphones. IR commands from the Receiver side can be extended to
sources connected to any of the Sender units. RS-232 serial control can also be extended
between each Sender and Receiver. The built-in web server interface makes operation,
set-up, and configuration simple and intuitive. The Gefen HD KVM over IP is the perfect
solution for large scale remote workstation access and digital signage applications.
a Gigabit Local Area Network. Resolutions up to 1080p Full HD and 1920 x 1200
(WUXGA) are supported. The Senders and Receivers can be automatically or manually
configured to unique IP addresses to allow the connection of multiple units to the same
network. Multiple Receiver units can simultaneously connect to any Sender unit within the
network including the Gefen KVM over LAN products with HDMI, DVI, or VGA video, to
create a virtual crosspoint matrix of just over 65,000 Sender and Receiver units total,
depending on the network bandwidth and number of ports on the network switch (see Note).
When using HDCP-encrypted content, only HDMI Senders and Receiver units can accept
and display the content. Each Receiver unit has a built-in Ethernet switch and two additional
RJ-45 Ethernet ports to allow for the connection of computers and other IP-enabled devices.
USB 2.0 data rates up to 480 Mbps are supported in addition to backward-compatibility
with USB 1.1. Each Receiver unit provides two USB ports with up to 500mA current draw per
connector, providing access to keyboard, mouse, and other compatible devices.
Bi-directional analog audio capability allows audio to be transported between the Sender
and the Receiver units. The built-in mic pre-amp on the Receiver unit ensures compatibility
with a variety of microphones. IR commands from the Receiver side can be extended to
sources connected to any of the Sender units. RS-232 serial control can also be extended
between each Sender and Receiver. The built-in web server interface makes operation,
set-up, and configuration simple and intuitive. The Gefen HD KVM over IP is the perfect
solution for large scale remote workstation access and digital signage applications.
How It Works
If you will be using multiple Sender units, use the built-in web interface to assign a unique
channel ID to each unit. Use the included HDMI cable to connect a computer or other HDMI
source to the Sender's HDMI input. Use the included USB and RS-232 cables to connect the
computer's USB and RS-232 interfaces to the Sender unit. Connect audio Line In and audio
Line Out as needed to the Sender. If your computer or other source is IR controllable,
connect a Gefen IR emitter to the Sender and attach it to the IR sensor lens of the source.
Connect the HDMI output of the Receiver to your Hi-Def display. Connect your USB devices,
RS-232 devices, microphone, and headphones or amplified speakers to the Receiver unit.
If the Receiver is not installed in the line-of-sight of the end-user, and IR commands will need
to be sent to the source, connect a Gefen IR extender (EXT-RMT-EXTIRC or EXT-RMT-EXTIRN)
to the Receiver. Connect the Sender and Receiver units to each other directly or through a
Gigabit Ethernet switch, using CAT-5e or better cables. Each cable run can be up to 330
feet (100 meters) in length. If the Sender is connected to your LAN, you can use the two
additional RJ-45 ports on the Receiver to connect computers and other IP enabled devices.
Connect the included 5V power supplies to the Sender and Receiver units and to available
electrical outlets. Power-on all associated equipment. Use the Mode button on the Sender to
optimize the picture for sharper still images or smoother video motion. When using multiple
Senders and Receivers as a "Virtual Matrix", use the Switch button on the Receiver or the web
interface to switch between Senders. When using multiple Senders and Receivers as a "Virtual
Matrix", you can connect to any of the Senders within the network by accessing the web
interface of each Receiver unit via a web browser on a mobile device or computer, or by
using the Gefen Keyboard Switching Controller software (available for download at
www.gefen.com).
channel ID to each unit. Use the included HDMI cable to connect a computer or other HDMI
source to the Sender's HDMI input. Use the included USB and RS-232 cables to connect the
computer's USB and RS-232 interfaces to the Sender unit. Connect audio Line In and audio
Line Out as needed to the Sender. If your computer or other source is IR controllable,
connect a Gefen IR emitter to the Sender and attach it to the IR sensor lens of the source.
Connect the HDMI output of the Receiver to your Hi-Def display. Connect your USB devices,
RS-232 devices, microphone, and headphones or amplified speakers to the Receiver unit.
If the Receiver is not installed in the line-of-sight of the end-user, and IR commands will need
to be sent to the source, connect a Gefen IR extender (EXT-RMT-EXTIRC or EXT-RMT-EXTIRN)
to the Receiver. Connect the Sender and Receiver units to each other directly or through a
Gigabit Ethernet switch, using CAT-5e or better cables. Each cable run can be up to 330
feet (100 meters) in length. If the Sender is connected to your LAN, you can use the two
additional RJ-45 ports on the Receiver to connect computers and other IP enabled devices.
Connect the included 5V power supplies to the Sender and Receiver units and to available
electrical outlets. Power-on all associated equipment. Use the Mode button on the Sender to
optimize the picture for sharper still images or smoother video motion. When using multiple
Senders and Receivers as a "Virtual Matrix", use the Switch button on the Receiver or the web
interface to switch between Senders. When using multiple Senders and Receivers as a "Virtual
Matrix", you can connect to any of the Senders within the network by accessing the web
interface of each Receiver unit via a web browser on a mobile device or computer, or by
using the Gefen Keyboard Switching Controller software (available for download at
www.gefen.com).
NOTE:
A Gigabit switch is required. The Gigabit switch must support 8k jumbo frame
packets in order for multicast mode to operate. If your LAN is not dedicated to Gefen
KVM-LAN products exclusively, then a managed switch is highly recommended.
KVM-LAN products exclusively, then a managed switch is highly recommended.
Features*
• Extends HDMI, USB, RS-232, bi-directional stereo analog audio, and IR
over IP, using a Gigabit Local Area Network
• Supports resolutions up to 1080p Full HD and 1920 x 1200 (WUXGA)
• Supported HDMI Features:
• HDCP
• Deep Color
• LPCM 7.1 audio, Dolby® TrueHD, and DTS-HD Master Audio™
• Lip-Sync pass-through
• Built-in web interface facilitates intuitive set up and operation
• Any of the Senders within a network can be accessed by any Receiver unit
via a web browser on a mobile device or computer, or by using the Gefen
Keyboard Switching Controller software (available for download at
over IP, using a Gigabit Local Area Network
• Supports resolutions up to 1080p Full HD and 1920 x 1200 (WUXGA)
• Supported HDMI Features:
• HDCP
• Deep Color
• LPCM 7.1 audio, Dolby® TrueHD, and DTS-HD Master Audio™
• Lip-Sync pass-through
• Built-in web interface facilitates intuitive set up and operation
• Any of the Senders within a network can be accessed by any Receiver unit
via a web browser on a mobile device or computer, or by using the Gefen
Keyboard Switching Controller software (available for download at
www.gefen.com)
• Supports a total of just over 65,000 Sender and Receiver units, depending on
the network bandwidth and number of ports on your network switch
• USB 2.0 data rates up to 480 Mbps and backward-compatibility with USB 1.1
• Three-port Gigabit Ethernet switch built into the Receiver unit
• Mode button on Sender for sharpness or motion optimization of image
• Field-upgradable firmware via web server interface
• Locking power supply connectors
• 1U tall, half-rack width enclosures are rack-mountable using EXT-RACK-1U
• Surface mounting brackets included
• Supports a total of just over 65,000 Sender and Receiver units, depending on
the network bandwidth and number of ports on your network switch
• USB 2.0 data rates up to 480 Mbps and backward-compatibility with USB 1.1
• Three-port Gigabit Ethernet switch built into the Receiver unit
• Mode button on Sender for sharpness or motion optimization of image
• Field-upgradable firmware via web server interface
• Locking power supply connectors
• 1U tall, half-rack width enclosures are rack-mountable using EXT-RACK-1U
• Surface mounting brackets included
Specifications*
•
Maximum Pixel Clock: 165 MHz
• Video Input Connector (Sender): (1) HDMI Type A 19-pin, female, locking
• Video Output Connector (Receiver): (1) HDMI Type A 19-pin, female, locking
• Line Input (Sender): (1) 3.5mm mini-stereo jack
• Line Output (Sender): (1) 3.5mm mini-stereo jack
• Mic Input (Receiver): (1) 3.5mm mini-stereo jack
• Line Output (Receiver): (1) 3.5mm mini-stereo jack
• USB Host Interface (Sender): (1) USB Type B, female
• USB Device Connectors (Receiver): (2) USB Type A, female
• RS-232 Connector (Sender): (1) DB-9, female
• RS-232 Connector (Receiver): (1) DB-9, male
• IR Emitter (Sender): (1) 3.5mm mini-mono jack
• IR Extender (Receiver): (1) 3.5mm mini-stereo jack
• Ethernet connector (Sender): (1) RJ-45, shielded
• Ethernet connectors (Receiver): (3) RJ-45, shielded
• Mode button (Sender): (1) tact-type
• ID Selector switch (Sender): (1) rotary-type
• Switch button (Receiver): (1) tact-type
• Reset button (Receiver): (1) tact-type, recessed
• Link Indicator (Sender/Receiver): (1) LED, green
• Power Indicator (Sender/Receiver): (1) LED, blue
• Power Supply (Sender / Receiver): 5V DC, locking
• Power Consumption (Sender / Receiver): 10W (max.)
• Dimensions (Sender / Receiver) (W x H x D): 8.4” x 1.7” x 4.5”
(213mm x 43mm x 113mm)
• Shipping Weight: EXT-HDKVM-LAN: 8.3 lbs. (3.8 kg)
EXT-HDKVM-LANTX: 5.7 lbs. (3.0 kg)
EXT-HDKVM-LANRX: 4.6 lbs. (2.0 kg)
• Video Output Connector (Receiver): (1) HDMI Type A 19-pin, female, locking
• Line Input (Sender): (1) 3.5mm mini-stereo jack
• Line Output (Sender): (1) 3.5mm mini-stereo jack
• Mic Input (Receiver): (1) 3.5mm mini-stereo jack
• Line Output (Receiver): (1) 3.5mm mini-stereo jack
• USB Host Interface (Sender): (1) USB Type B, female
• USB Device Connectors (Receiver): (2) USB Type A, female
• RS-232 Connector (Sender): (1) DB-9, female
• RS-232 Connector (Receiver): (1) DB-9, male
• IR Emitter (Sender): (1) 3.5mm mini-mono jack
• IR Extender (Receiver): (1) 3.5mm mini-stereo jack
• Ethernet connector (Sender): (1) RJ-45, shielded
• Ethernet connectors (Receiver): (3) RJ-45, shielded
• Mode button (Sender): (1) tact-type
• ID Selector switch (Sender): (1) rotary-type
• Switch button (Receiver): (1) tact-type
• Reset button (Receiver): (1) tact-type, recessed
• Link Indicator (Sender/Receiver): (1) LED, green
• Power Indicator (Sender/Receiver): (1) LED, blue
• Power Supply (Sender / Receiver): 5V DC, locking
• Power Consumption (Sender / Receiver): 10W (max.)
• Dimensions (Sender / Receiver) (W x H x D): 8.4” x 1.7” x 4.5”
(213mm x 43mm x 113mm)
• Shipping Weight: EXT-HDKVM-LAN: 8.3 lbs. (3.8 kg)
EXT-HDKVM-LANTX: 5.7 lbs. (3.0 kg)
EXT-HDKVM-LANRX: 4.6 lbs. (2.0 kg)
HDMI KVM Extender over IP
EXT-HDKVM-LAN
REV. A11
1080P
®
Gefen LLC.
20600 Nordhoff Street, Chatsworth CA 91311
Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120
www.gefen.com
* Features and specifications subject to change without notice.
All trademarks and registered trademarks are properties of their respective owners
Copyright© 2015 Gefen LLC.
KVM
over
IP