Havis C-3010 Manuale Utente
C-1800_INST_6-09
INSTALLATION OPTIONS:
1. MOUNT C-SERIES CONSOLE TO TRAK MOUNT:
• Mount hump bracket and trak assembly to vehicle. (See specific C-TM instructions)
• Sub-assemble console mounting brackets to console and position on trak mount.
• Slide ¼ x ¾” bolts in slide rails of trak and attach to consoles’ front mounting bracket.
• Adjust console on trak. Determine positioning before continuing.
• Attach rear console mounting bracket to vehicle. Mark and pre-drill mounting holes.
• Sub-assemble console mounting brackets to console and position on trak mount.
• Slide ¼ x ¾” bolts in slide rails of trak and attach to consoles’ front mounting bracket.
• Adjust console on trak. Determine positioning before continuing.
• Attach rear console mounting bracket to vehicle. Mark and pre-drill mounting holes.
Attach to vehicle using ¼” x ¾” Hex head lag bolts.
Note: Be sure to check for obstructions prior to drilling.
2. MOUNT CONTROL HEAD(s) TO TRAK:
••••
Attach C-3061-x (depending on application) to control head. (Radio, siren, etc..)
• Slide ¼ x ¾” bolts in slide rails of trak and loosely attach using ¼” serrated nuts.
••••
Position control head and tighten.
3. MOUNT ANGLED/STOUT SERIES CONSOLE TO TRAK MOUNT:
• Mount hump bracket and trak assembly to vehicle.
• Slide ¼ x ¾” bolts in slide rails of trak and loosely attach using ¼” serrated nuts.
• Position console and tighten.
• Slide ¼ x ¾” bolts in slide rails of trak and loosely attach using ¼” serrated nuts.
• Position console and tighten.
4. MOUNT ANGLED CONSOLE TO TRANSMISSION HUMP BRACKET:
••••
Sub-assemble ¼” x ¾” carriage bolts w/ retaining washers to transmission hump bracket.
••••
Install transmission hump bracket to inner front seat bolts.
• Position console on transmission hump bracket so that carriage bolts align w/ slots in
console and loosely attach ¼” serrated nuts
••••
Adjust console and tighten.
5. MOUNT C-SERIES CONSOLE TO TRANSMISSION HUMP BRACKET:
••••
Sub-assemble ¼” x ¾” carriage bolts w/ retaining washers to transmission hump bracket.
••••
Install transmission hump bracket to inner front seat bolts.
• Sub-assemble console mounting bracket(s) depending on particular application.
• Position console on transmission hump bracket so that carriage bolts align w/ slots in
• Position console on transmission hump bracket so that carriage bolts align w/ slots in
console mounting bracket(s) and loosely attach ¼” serrated nuts.
• Some applications use a rear leg that bolts to the floor of the vehicle. In this application
pre-drill floor using 3/16” hole and attach leg using ¼” x ¾” lag bolt.
6. MOUNT C-SERIES CONSOLE TO FLOOR OF VEHICLE:
••••
Check vehicle for obstructions. (Wire harnesses, fuel lines, hoses, drive shaft, etc…)
• Sub-assemble console mounting bracket(s) depending on particular application.
••••
Position console, mark, & pre-drill floor of vehicle using 3/16” drill bit.
••••
Mount console brackets to vehicles using ¼” x ¾” lag bolts.
Note: Longer bolts may be necessary in some applications. (Not included)
7. MOUNT ANGLED SERIES/STOUT SERIES CONSOLE TO FLOOR OF VEHILCE:
••••
Check vehicle for obstructions. (Wire harnesses, fuel lines, hoses, drive shaft, etc.)
••••
Position console, mark, & pre-drill floor of vehicle using 3/16” drill bit.
••••
Mount console to vehicle using ¼” x ¾” lag bolts.
Note: Longer bolts may be necessary in some applications. (Not included)
2