Alcatel-Lucent OAW-IAP205 Manuale Utente

2

Alcatel-Lucent OmniAccess 200 Series Access Points

•  AP205 and IAP205

¬ 2.4 GHz (300 Mb/s max rate) and 5 GHz 

(867 Mb/s max rate) radios, each with  
2 x 2 MIMO and four integrated omni-
directional downtilt antennas

•  AP204 and IAP204

¬ 2.4 GHz (300 Mb/s max rate) and 5 GHz 

(867 Mb/s max rate) radios, each with  
2 x 2 MIMO and two combined, diplexed 
external RP-SMA antenna connectors

•  RF management

¬ Adaptive Radio Management™ (ARM) 

technology automatically assigns 
channel and power settings, provides 
airtime fairness and ensures APs stay 
clear of all sources of RF interference 
to deliver reliable, high-performance 
WLANs

¬ 200 Series APs can be configured to 

provide part-time or dedicated air 
monitoring for spectrum analysis and 
wireless intrusion protection, virtual 
private network (VPN) tunnels to extend 
remote locations to corporate resources, 
and wireless mesh connections where 
Ethernet drops are not available

•  Spectrum analysis

¬ Capable of part-time or dedicated air 

monitoring, the spectrum analyzer 
remotely scans the 2.4 GHz and 5 GHz 
radio bands to identify sources of RF 
interference

• Security

¬ Integrated Trusted Platform Module 

(TPM) to securely store credentials  
and keys

¬ SecureJack-capable to securely tunnel 

wired Ethernet traffic

•  Instant AP
•  Mobility Controller-managed AP
•  RAP for branch deployments
•  Air monitor (AM) for wireless intrusion 

detection system (WIDS), rogue detection 
and containment

•  Spectrum analyzer, dedicated or hybrid
•  Secure enterprise mesh

 

•  AP type: Indoor, dual radio, 5 GHz 

802.11ac and 2.4 GHz 802.11n 2 x 2:2

•  Software-configurable dual radio supports 

5 GHz (Radio 0) and 2.4 GHz (Radio 1)

•  2 x 2 MIMO with two spatial streams and 

up to 867 Mb/s wireless data rate

•  Supported frequency bands (country-

specific restrictions apply):
¬ 2.4000 GHz to 2.4835 GHz
¬ 5.150 GHz to 5.250 GHz
¬ 5.250 GHz to 5.350 GHz
¬ 5.470 GHz to 5.725 GHz
¬ 5.725 GHz to 5.850 GHz

•  Available channels: Dependent on 

configured regulatory domain

•  Dynamic frequency selection (DFS) 

optimizes available RF spectrum use

•  Supported radio technologies:

¬ 802.11b: Direct-sequence spread 

spectrum (DSSS)

¬ 802.11a/g/n/ac: Orthogonal frequency-

division multiplexing (OFDM)

•  Supported modulation types:

¬ 802.11b: Binary phase-shift keying 

(BPSK), quadrature phase shift keying 
(QPSK), Complementary Code Keying 
(CCK)

¬ 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 

64-QAM, 256-QAM

•  Transmit power: Configurable in 

increments of 0.5 dBm

•  Maximum (aggregate, conducted total) 

transmit power (limited by local regulatory 
requirements):
¬ 2.4 GHz band: +21 dBm  

(18 dBm per chain)

¬ 5 GHz band: +21 dBm  

(18 dBm per chain)

•  Advanced Cellular Coexistence (ACC) 

minimizes interference from cellular 
networks

•  Maximum ratio combining (MRC)  

for improved receiver performance

•  Cyclic delay/shift diversity (CDD/CSD)  

for improved downlink RF performance

•  Short guard interval for 20 MHz, 40 MHz 

and 80 MHz channels

•  Space-time block coding (STBC) for 

increased range and improved reception

•  Low-density parity check (LDPC) for high-

efficiency error correction and increased 
throughput

•  Transmit beamforming (TxBF) for 

increased reliability in signal delivery

•  Supported data rates (Mb/s):

¬ 802.11b: 1, 2, 5.5, 11
¬ 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
¬ 802.11n: 6.5 to 300 (MCS0 to MCS15)
¬ 802.11ac: 6.5 to 867 (MCS0 to MCS9, 

NSS = 1 to 2)

•  802.11n high-throughput (HT) support:  

HT 20/40

•  802.11ac very high throughput (VHT) 

support: VHT 20/40/80

•  802.11n/ac packet aggregation: A-MPDu, 

A-MSDu

•  AP204/IAP204: Two RP-SMA connectors 

for external dual-band antennas. Internal 
loss between radio interface and external 
antenna connectors (due to diplexing 
circuitry): 1.5 dB in 2.4 GHz and 3.0 dB  
in 5 GHz

•  AP205/IAP205: Four integrated down-tilt 

omni- directional antennas for 2 x 2 MIMO 
with maximum antenna gain of 4.0 dBi 
in 2.4 GHz and 6.0 dBi in 5 GHz. built-in 
antennas are optimized for horizontal 
ceiling-mounted orientation of the AP

•  10/100/1000BASE-T Ethernet network 

interface (RJ-45)
¬ Auto-sensing link speed and MDI/MDX
¬ 802.3az Energy-Efficient Ethernet (EEE)
¬ Power over Ethernet (PoE)-PD: 48-V DC 

(nominal) 802.3af PoE

•  DC power interface, accepts 1.7 mm/ 

4.0 mm center-positive circular plug with 
9.5 mm length

•  Visual indicators (LEDs):

¬ Power/system status
¬ Ethernet link status (ENET)
¬ Radio status (two; RAD0, RAD1)

•  Reset button: factory reset (during device 

power up)

•  Serial console interface (RJ-45)
•  Kensington security slot

•  Maximum (worst-case) power 

consumption: 12.5 W (PoE) or 11.7 W (DC)

•  Maximum (worst-case) power consumption 

in idle mode: 8.4 W (PoE) or 7.7 W (DC)

•  Direct DC source: 12-V DC nominal, +/- 5%
•  PoE: 48-V DC (nominal) 802.3af-compliant 

source

•  Power sources sold separately
•  When both power sources are available, 

DC power takes priority